Provided by: plc-utils-extra_0.0.6+git20230504.1ba7d5a0-1_amd64 
NAME
coqos_add - Add a managed data stream
SYNOPSIS
coqos_add action priority rate ttl operand condition [condition] [...] [device] [...]
DESCRIPTION
This page is under construction.
Add a managed stream to one or more powerline devices using the VS_CONN_ADD message. Consult the
Qualcomm Atheros Firmware Technical Reference Manual for a description of this vendor specific message
type.
This program is part of the Qualcomm Atheros Powerline Toolkit. See the plc man page for an overview and
installation instructions.
BACKGROUND
Bandwidth management prioritizes streams so that data from lowest priority stream is dropped first
whenever one of the following conditions is detected. This ensures that the remaining streams continue
operate at their full pontential.
Degraded line condition
The channel degrades to the point where the available PHY rate from the transmitter to the
receiver is too low due to the variability of the power line.s characteristics.
Over subscription
Too much data is being sent per second, resulting in packet loss due to excessive collisions due
to excessive channel oversubscription.
Lack of channel Capacity
On starting new source there is not enough channel capacity to support it.
OPTIONS
-e Redirects stderr messages to stdout. By convention progress messages and error messages are
printed on stderr while primary program output is printed on stdout. This option prints all
output on stdout in cases where this is desired.
-i interface
Select the host Ethernet interface. All requests are sent via this host interface and only
reponses received via this host interface are recognized. The default interface is eth1 because
most people use eth0 as their principle network connection; however, if environment string "PLC"
is defined then it takes precedence over the default interface. This option then takes precedence
over either default.
-q Suppresses status messages on stderr.
-r Display relative memory offsets on output. This option is the default.
-v Prints additional information on stdout. In particular, this option dumps outgoing Ethernet
packets on stdout.
-?,--help
Displays program help information on stderr. This option takes precedence over all other options
on the command line except version information.
-!,--version
Displays program version information on stderr. This option takes precedence over all other
options on the command line except help information. Use this option when sending screen dumps to
Atheros technical staff.
ARGUMENTS
action The action taken for frames that satisfy the selection criteria. Valid actions are "CAP0",
"CAP1", "CAP2", "CAP3" to specify the channel access priority queue. CAP0 and CAP1 are for best
effort data. CAP2 is for video and non urgent MMEs. CAP3 is for voice, urgent MMEs and control
messages such as IGMP and MLD.
priority
The relative priority of this stream. Valid values are 0 through 15 where 0 is the lowest
priority and 15 is the highest.
destination
The destination MAC address.
rate The average expected data rate for this stream. Valid values are 1 to 9000 where units are in
10kbps so the minimum rate is 10kbps and the maximum rate is 90mbps.
ttl The time to live for this stream. Valid values are 10000 to 2000000 where units are in
microseconds so the minimum is time is 10 milliseconds and the maximum time is 2 seconds.
operand
The operand specifies the logical relationship between conditions before the action to be taken.
Valid operands are listed and described under OPERANDS.
condition
A conditional expression consisting of a field, operator and value. See CONDITIONS for more
information.
device The MAC address of some powerline device. More than one address may be specified on the command
line. If more than one address is specified then operations are performed on each device in turn.
The default address is "local". See DEVICES for more information.
CONDITIONS
A condition consists of a field, an operator and a value. One condition is required but three are
permitted. Condition order is not important but all conditions must appear after the operand and before
the control.
field The field is the part of the Ethernet frame to be examined. Some fields are not valid for some
actions but this program does not enforce such rules since validation is performed by runtime
firmware on each device. Recognized fields are listed and described under FIELDS.
operator
The operator specifies the relationsip that must exist between the field and value in order for
the condition to evaluate True. Currently, only equality operators are supported. Valid
operators are listed and described under OPERATORS.
value The value must be appropriate to the field type. Some fields are MAC or IP addresses, some are
integers, some are bitmaps and others are states. Integers and bitmaps may be expressed in
binary, decimal or hexadecimal format. Binary values staRt with 0b. Hexadecimal values start
with 0x. States are expressed using keywords. Users are responsible for knowing how many bits
are significant for each type of value. Valid values are described along with fields under
FIELDS.
OPERANDS
The operand indicates the logical relationship that must exist between conditions in the rule set before
the action is applied to a frame. Operands are expressed as discrete alphanumeric strings entered in
upper, lower or mixed character case. Failure to enter a known operand will result in an error message
that lists all possible operands. They are positon sensitive. One operand is allowed and it must appear
after the action and before any condition.
Any Apply the action to frames that satisfy any of the conditions. This is equivalent to the logical
or operation.
All Apply the action to frames that satisfy all of the conditions. This is equivalent to the logical
and operation.
Always Apply the action to all frames, regardless of any and all conditions that may be specified.
FIELDS
Fields indicate the portion of the frame that is inspected during selection and the size and format of
the value permited in the condition statement. They are expressed as discrete alphanumeric strings
entered in upper, lower or mixed character case. Failure to enter a known field will result in an error
message that lists all possible fields.
ET A 16-bit Ethertype expressed in decimal, hexadecimal or binary. The format is described in IEEE
Standard 802-2001 [4].
EthDA A 48-bit Ethernet destination address expressed in hexadecimal. The format is described in IEEE
Standard 802-2001 [4].
EthSA A 48-bit Ethernet source address expressed in hexadecimal. The format is described in IEEE
Standard 802-2001 [4].
VLANUP An 8-bit Ethernet VLAN tag where the lower 3 bits are the User Priority sub-field of a VLAN Tag
defined in IEEE Std 802.1Q-1998 (Virtual Bridged Local Area Networks) [11]. The upper 5 bits
should be zero.
VLANID A 16-bit VLAN identifier where the lower 12 bits are the VLAN Identifier (VID) defined in IEEE Std
802.1Q-1998 (Virtual Bridged Local Area Networks) [11]. The upper 4 bits should be zero.
IPV4TOS
An 8-bit Type-of-Service code where the format is defined in the RFC 791 (Internet Protocol) [14].
IPV4PROT
An 8-bit Ethernet Protocol identifier. The format is defined in the RFC 791 (Internet Protocol)
[14].
IPV4SA A 32-bit Internet Protocol source address expressed in dotted-decimal notation. The official
format is defined in RFC 791 (Internet Protocol) [14]. Our implementation permits empty octets
and leading zeros within fields. For example, "..." is equivalent to "0.0.0.0 and "127..000.001"
is equivalent to "127.0.0.1".
IPV4DA A 32-bit Internet Protocol destination address expressed in dotted-decimal notation. The official
format is defined in RFC 791 (internet Protocol) [14]. Our implementation permits empty octets and
leading zeros within fields. For example, "..." is equivalent to "0.0.0.0 and "127..000.001" is
equivalent to "127.0.0.1".
IPV6TC An 8-bit Internet Protocol V6 traffic class expressed as defined in RFC 2460 (Internet Protocol
Version 6) [17].
IPV6FL A 24-bit IPV6 flow label where the lower 20 bits are the IPv6 Flow Label defined in RFC 2460
(Internat Protocol Version 6) [17]. The upper 4 bits should be zero. The value can be entered
either as a decimal, binary or hex integer.
IPV6SA A 128-bit IPV6 source address expressed as colon-separated hexadecmial quartets (octet pairs).
The official format is defined in RFC 2460 (Internet Protocol Version 6) [17]. Our implementation
permits multiple empty fields, abreviated fields and leading zeros within fields. When multiple
empty fields appear, only the right-most occurance expands to zeros. For example,
"FFFF::DDDD::BBBB::AAAA" is equivalent to "FFFF:0000:DDDD:0000:BBBB:0000:0000:AAAA".
IPV6DA A 128-bit IPV6 destination address expressed as colon-separated hexadecimal quartets (octet
pairs). The official format is defined in RFC 2460 (Internet Protocol Version 6) [17]. Our
implementation permits multiple empty fields, abbreviated fields and leading zeros within fields.
When multiple empty fields appear, only the right-most occurance expands to zeros. For example,
"AAAA::BBBB::CCCC::DDDD" is equivalent to "AAAA:0000:BBBB:0000:CCCC:0000:0000:DDDD".
TCPSP A 16-bit TCP source port as a decimal integer. The format is defined in RFC 793 (Transmission
Control Protocol [15]).
TCPDP A 16-bit TCP destination port expressed as a decimal integer. The format is defined in RFC 793
(Transmission Control Protocol [15]).
UDPSP A 16-bit UDP source port expressed as a decimal integer. The format is defined in RFC 768 (User
Datagram Protocol [13]).
UDPDP A 16-bit UDP destination port expressed as a decimal integer. The format is defined in RFC 768
(User Datagram Protocol [13]).
IPSP A 16-bit IP source port expressed as a decimal integer. This condition applies to either TCP or
UDP packets, depending on the protocol used, and is valid only for actions "CAP0", "CAP1", "CAP2",
"CAP3" and "Drop".
IPDP A 16-bit IP destination port expressed as a decimal integer. This condition applies to either TCP
or UDP packets, depending on the protocol used, and is valid only for actions "CAP0", "CAP1",
"CAP2", "CAP3" and "Drop".
MME A 24-bit Atheros HomePlugAV Management Message type expressed in hexadecimal. The first byte is
the MMV and the next two bytes are the MMTYPE for a HomePlug AV frame as defined in the HomePlug
AV Specification. The MMTYPE will match any MME sub-type (Request; Confirm; Indicate; Response).
This field is only valid for action "Boost".
OPERATORS
An operator indicates an equality between a field and a value. An operator is an alphanumeric string
entered in upper, lower or mixed character case. Failure to enter a known operator will result in an
error message that lists all possible operators. Operators are position sensitive and must appear
between each field and value.
Is Indicates that the frame field must equal the associated value for the condition to evaluate true.
Not Indicates that the frame field must not equal the associated value for the condition to true true.
STATES
A state is a special case of value.
True,On,Yes,Present
Indicates a positive state or presence of some entity. All are equivalent and can be used
interchangeably. Double negatives are permitted so "Is True" is equvalent to "Not False".
False,Off,No,Missing
Indicates a negative state or absence of some entity. ALl are equivalent and can be used
interchangeably. Double negatives are permitted so "Is False" is equvalent to "Not True".
DEVICES
Powerline devices use Ethernet Media Access Control (MAC) addresses. A MAC address is a 48-bit value
entered as 12 hexadecimal digits in upper, lower or mixed character case. Octets may be separated with
colons for clarity. For example, "00b052000001", "00:b0:52:00:00:01" and "00b052:000001" are valid and
equivalent.
The following MAC addresses are common or special and may be entered by name instead of number.
all Same as "broadcast".
broadcast
A synonym for the Ethernet broadcast address, FF:FF:FF:FF:FF:FF. All devices, whether local,
remote or foreign recognize messages sent to this address. A remote device is any device at the
far end of a powerline connection. A foreign device is any device not manufactured by Atheros.
local A synonym for the Qualcomm Atheros vendor specific Local Management Address (LMA),
00:B0:52:00:00:01. All local Atheros devices recognize this address but remote and foreign
devices do not. A remote device is any device at the far end of a powerline connection. A
foreign device is any device not manufactured by Atheros.
REFERENCES
See the Qualcomm Atheros HomePlug AV Firmware Technical Reference Manual for more information.
DISCLAIMER
Atheros HomePlug AV Vendor Specific Management Message structure and content is proprietary to Qualcomm
Atheros, Ocala FL USA. Consequently, public information may not be available. Qualcomm Atheros reserves
the right to modify message structure and content in future firmware releases without any obligation to
notify or compensate users of this program.
EXAMPLES
The following example adds a temporary stream to device 00:b0:52:BA:BE:01 which will then manage the
bandwidth for that stream until removed with program coqos_rel.
# coqos_add CAP2 15 5000 200000 any ethda is 192.168.105 00:B0:52:BA:BE:01
This adds a stream to the bandwidth manager that sets all traffic to destination address of 192.168.0.105
as priority 15 (the highest priority). This would then need to also be sent to each device on the
network. Refer to int6krule for more details on how to specify conditions.
SEE ALSO
coqos_info(1), coqos_man(1), coqos_mod(1), coqos_rel(1)
CREDITS
Bill Wike
Nathaniel Houghton
Charles Maier
open-plc-utils-0.0.3 November 2013 coqos_add(1)