Ubuntu Manpage: tset, reset - terminal initialization

Provided by: ncurses-bin_6.3-2ubuntu0.1_amd64

NAME

       tset, reset - terminal initialization

SYNOPSIS

       tset [-IQVcqrsw] [-] [-e ch] [-i ch] [-k ch] [-m mapping] [terminal]
       reset [-IQVcqrsw] [-] [-e ch] [-i ch] [-k ch] [-m mapping] [terminal]

DESCRIPTION

tset - initialization
This program initializes terminals.

First, tset retrieves the current terminal mode settings for your terminal. It does this by successively
testing

• the standard error,

• standard output,

• standard input and

• ultimately “/dev/tty”

to obtain terminal settings. Having retrieved these settings, tset remembers which file descriptor to
use when updating settings.

Next, tset determines the type of terminal that you are using. This determination is done as follows,
using the first terminal type found.

1. The terminal argument specified on the command line.

2. The value of the TERM environmental variable.

3. (BSD systems only.) The terminal type associated with the standard error output device in the
/etc/ttys file. (On System-V-like UNIXes and systems using that convention, getty does this job by
setting TERM according to the type passed to it by /etc/inittab.)

4. The default terminal type, “unknown”.

If the terminal type was not specified on the command-line, the -m option mappings are then applied (see
the section TERMINAL TYPE MAPPING for more information). Then, if the terminal type begins with a
question mark (“?”), the user is prompted for confirmation of the terminal type. An empty response
confirms the type, or, another type can be entered to specify a new type. Once the terminal type has
been determined, the terminal description for the terminal is retrieved. If no terminal description is
found for the type, the user is prompted for another terminal type.

Once the terminal description is retrieved,

• if the “-w” option is enabled, tset may update the terminal's window size.

If the window size cannot be obtained from the operating system, but the terminal description (or
environment, e.g., LINES and COLUMNS variables specify this), use this to set the operating system's
notion of the window size.

• if the “-c” option is enabled, the backspace, interrupt and line kill characters (among many other
things) are set

• unless the “-I” option is enabled, the terminal and tab initialization strings are sent to the
standard error output, and tset waits one second (in case a hardware reset was issued).

• Finally, if the erase, interrupt and line kill characters have changed, or are not set to their
default values, their values are displayed to the standard error output.

reset - reinitialization
When invoked as reset, tset sets the terminal modes to “sane” values:

• sets cooked and echo modes,

• turns off cbreak and raw modes,

• turns on newline translation and

• resets any unset special characters to their default values

before doing the terminal initialization described above. Also, rather than using the terminal
initialization strings, it uses the terminal reset strings.

The reset command is useful after a program dies leaving a terminal in an abnormal state:

• you may have to type

<LF>reset<LF>

(the line-feed character is normally control-J) to get the terminal to work, as carriage-return may
no longer work in the abnormal state.

• Also, the terminal will often not echo the command.

OPTIONS

The options are as follows:

-c Set control characters and modes.

-e ch
Set the erase character to ch.

-I Do not send the terminal or tab initialization strings to the terminal.

-i ch
Set the interrupt character to ch.

-k ch
Set the line kill character to ch.

-m mapping
Specify a mapping from a port type to a terminal. See the section TERMINAL TYPE MAPPING for more
information.

-Q Do not display any values for the erase, interrupt and line kill characters. Normally tset displays
the values for control characters which differ from the system's default values.

-q The terminal type is displayed to the standard output, and the terminal is not initialized in any
way. The option “-” by itself is equivalent but archaic.

-r Print the terminal type to the standard error output.

-s Print the sequence of shell commands to initialize the environment variable TERM to the standard
output. See the section SETTING THE ENVIRONMENT for details.

-V reports the version of ncurses which was used in this program, and exits.

-w Resize the window to match the size deduced via setupterm(3X). Normally this has no effect, unless
setupterm is not able to detect the window size.

The arguments for the -e, -i, and -k options may either be entered as actual characters or by using the
“hat” notation, i.e., control-h may be specified as “^H” or “^h”.

If neither -c or -w is given, both options are assumed.

SETTING THE ENVIRONMENT

       It is often desirable to enter the terminal type and information about the terminal's  capabilities  into
       the shell's environment.  This is done using the -s option.

       When  the  -s option is specified, the commands to enter the information into the shell's environment are
       written to the standard output.  If the SHELL environmental variable ends in “csh”, the commands are  for
       csh, otherwise, they are for sh.  Note, the csh commands set and unset the shell variable noglob, leaving
       it unset.  The following line in the .login or .profile files will initialize the environment correctly:

           eval `tset -s options ... `

TERMINAL TYPE MAPPING

When the terminal is not hardwired into the system (or the current system information is incorrect) the
terminal type derived from the /etc/ttys file or the TERM environmental variable is often something
generic like network, dialup, or unknown. When tset is used in a startup script it is often desirable to
provide information about the type of terminal used on such ports.

The -m options maps from some set of conditions to a terminal type, that is, to tell tset “If I'm on this
port at a particular speed, guess that I'm on that kind of terminal”.

The argument to the -m option consists of an optional port type, an optional operator, an optional baud
rate specification, an optional colon (“:”) character and a terminal type. The port type is a string
(delimited by either the operator or the colon character). The operator may be any combination of “>”,
“<”, “@”, and “!”; “>” means greater than, “<” means less than, “@” means equal to and “!” inverts the
sense of the test. The baud rate is specified as a number and is compared with the speed of the standard
error output (which should be the control terminal). The terminal type is a string.

If the terminal type is not specified on the command line, the -m mappings are applied to the terminal
type. If the port type and baud rate match the mapping, the terminal type specified in the mapping
replaces the current type. If more than one mapping is specified, the first applicable mapping is used.

For example, consider the following mapping: dialup>9600:vt100. The port type is dialup , the operator
is >, the baud rate specification is 9600, and the terminal type is vt100. The result of this mapping is
to specify that if the terminal type is dialup, and the baud rate is greater than 9600 baud, a terminal
type of vt100 will be used.

If no baud rate is specified, the terminal type will match any baud rate. If no port type is specified,
the terminal type will match any port type. For example, -m dialup:vt100 -m :?xterm will cause any
dialup port, regardless of baud rate, to match the terminal type vt100, and any non-dialup port type to
match the terminal type ?xterm. Note, because of the leading question mark, the user will be queried on
a default port as to whether they are actually using an xterm terminal.

No whitespace characters are permitted in the -m option argument. Also, to avoid problems with meta-
characters, it is suggested that the entire -m option argument be placed within single quote characters,
and that csh users insert a backslash character (“\”) before any exclamation marks (“!”).

HISTORY

       A  reset  command  appeared in 1BSD (March 1978), written by Kurt Shoens.  This program set the erase and
       kill characters to ^H (backspace) and @ respectively.  Mark Horton improved that in 3BSD (October  1979),
       adding  intr,  quit, start/stop and eof characters as well as changing the program to avoid modifying any
       user settings.  That version of reset did not use the termcap database.

       A separate tset command was provided in 1BSD by  Eric  Allman,  using  the  termcap  database.   Allman's
       comments  in the source code indicate that he began work in October 1977, continuing development over the
       next few years.

       According to comments in the source code, the tset program was modified in September 1980, to  use  logic
       copied  from  the  3BSD  “reset” when it was invoked as reset.  This version appeared in 4.1cBSD, late in
       1982.

       Other developers (e.g., Keith Bostic and Jim Bloom) continued to modify tset until 4.4BSD was released in
       1993.

       The ncurses implementation was lightly adapted from the 4.4BSD sources for a terminfo environment by Eric
       S. Raymond <esr@snark.thyrsus.com>.

COMPATIBILITY

Neither IEEE Std 1003.1/The Open Group Base Specifications Issue 7 (POSIX.1-2008) nor X/Open Curses Issue
7 documents tset or reset.

The AT&T tput utility (AIX, HPUX, Solaris) incorporated the terminal-mode manipulation as well as
termcap-based features such as resetting tabstops from tset in BSD (4.1c), presumably with the intention
of making tset obsolete. However, each of those systems still provides tset. In fact, the commonly-used
reset utility is always an alias for tset.

The tset utility provides for backward-compatibility with BSD environments (under most modern UNIXes,
/etc/inittab and getty(8) can set TERM appropriately for each dial-up line; this obviates what was tset's
most important use). This implementation behaves like 4.4BSD tset, with a few exceptions specified here.

A few options are different because the TERMCAP variable is no longer supported under terminfo-based
ncurses:

• The -S option of BSD tset no longer works; it prints an error message to the standard error and dies.

• The -s option only sets TERM, not TERMCAP.

There was an undocumented 4.4BSD feature that invoking tset via a link named “TSET” (or via any other
name beginning with an upper-case letter) set the terminal to use upper-case only. This feature has been
omitted.

The -A, -E, -h, -u and -v options were deleted from the tset utility in 4.4BSD. None of them were
documented in 4.3BSD and all are of limited utility at best. The -a, -d, and -p options are similarly
not documented or useful, but were retained as they appear to be in widespread use. It is strongly
recommended that any usage of these three options be changed to use the -m option instead. The -a, -d,
and -p options are therefore omitted from the usage summary above.

Very old systems, e.g., 3BSD, used a different terminal driver which was replaced in 4BSD in the early
1980s. To accommodate these older systems, the 4BSD tset provided a -n option to specify that the new
terminal driver should be used. This implementation does not provide that choice.

It is still permissible to specify the -e, -i, and -k options without arguments, although it is strongly
recommended that such usage be fixed to explicitly specify the character.

As of 4.4BSD, executing tset as reset no longer implies the -Q option. Also, the interaction between the
- option and the terminal argument in some historic implementations of tset has been removed.

The -c and -w options are not found in earlier implementations. However, a different window size-change
feature was provided in 4.4BSD.

• In 4.4BSD, tset uses the window size from the termcap description to set the window size if tset is
not able to obtain the window size from the operating system.

• In ncurses, tset obtains the window size using setupterm, which may be from the operating system, the
LINES and COLUMNS environment variables or the terminal description.

Obtaining the window size from the terminal description is common to both implementations, but considered
obsolescent. Its only practical use is for hardware terminals. Generally speaking, a window size would
be unset only if there were some problem obtaining the value from the operating system (and setupterm
would still fail). For that reason, the LINES and COLUMNS environment variables may be useful for
working around window-size problems. Those have the drawback that if the window is resized, those
variables must be recomputed and reassigned. To do this more easily, use the resize(1) program.

ENVIRONMENT

       The tset command uses these environment variables:

       SHELL
            tells tset whether to initialize TERM using sh or csh syntax.

       TERM Denotes your terminal type.  Each terminal type is distinct, though many are similar.

       TERMCAP
            may denote the location of a termcap database.  If it is not an absolute pathname, e.g., begins with
            a “/”, tset removes the variable from the environment before looking for the terminal description.

FILES

       /etc/ttys
            system port name to terminal type mapping database (BSD versions only).

       /etc/terminfo
            terminal capability database