Provided by: sg3-utils_1.48-2ubuntu1_amd64 
NAME
sg_senddiag - performs a SCSI SEND DIAGNOSTIC command
SYNOPSIS
sg_senddiag [--doff] [--extdur] [--help] [--hex] [--list] [--maxlen=LEN] [--page=PG] [--pf]
[--raw=H,H...] [--raw=-] [--selftest=ST] [--test] [--timeout=SECS] [--uoff] [--verbose] [--version]
DEVICE
sg_senddiag [-doff] [-e] [-h] [-H] [-l] [-pf] [-raw=H,H...] [-raw=-] [-s=ST] [-t] [-T=SECS] [-uoff] [-v]
[-V] [-?] DEVICE
DESCRIPTION
This utility sends a SCSI SEND DIAGNOSTIC command to the DEVICE. It can issue self-tests, find supported
diagnostic pages or send arbitrary diagnostic pages.
When the --list option and a DEVICE are given then the utility sends a SCSI RECEIVE DIAGNOSTIC RESULTS
command to fetch the response (i.e. the page numbers of supported diagnostic pages).
When the --list option is given without a DEVICE then a list of diagnostic page names and their numbers,
known by this utility, are listed.
This utility supports two command line syntax-es, the preferred one is shown first in the synopsis and
explained in this section. A later section on the old command line syntax outlines the second group of
options.
OPTIONS
Arguments to long options are mandatory for short options as well.
-d, --doff
set the Device Offline (DevOffL) bit (default is clear). Only significant when --test option is
set for the default self-test. When set other operations on any logical units controlled by the
this device server (target) may be affected (delayed) while a default self-test is underway.
-e, --extdur
outputs the expected extended self-test duration. The duration is given in seconds (and minutes in
parentheses). This figure is obtained from mode page 0xa (i.e. the control mode page).
-h, --help
print usage message then exit.
-H, --hex
outputs response from RECEIVE DIAGNOSTIC RESULTS in hex rather than decode it. Only the Supported
Diagnostic Pages diagnostic page (i.e. page_code=0) is decoded; other pages (e.g. those used by
SES) are output in hex.
If --hex is used once, the hex output has a relative address at the start of each line. If --hex
is used twice, then ASCII is shown to the right of each line of hex. If --hex is used three time
or more, only the hex is output, in two character pairs (i.e. a byte) space separated and up to 16
bytes per line. This latter form, if placed in a file or piped through to another invocation, is
suitable for the --raw=- option.
-l, --list
when a DEVICE is also given lists the names of all diagnostic pages supported by this device. The
request is sent via a SEND DIAGNOSTIC command (with the "pF" bit set) and the response is fetched
by a RECEIVE DIAGNOSTIC RESULTS command. When used in the absence of a --list argument then a list
of diagnostic page names and their numbers, known by this utility, are listed.
-m, --maxlen=LEN
where LEN is the value placed in the parameter list length field of a SEND DIAGNOSTIC command or
in the allocation length field of a RECEIVE DIAGNOSTIC RESULTS command. This only occurs when the
other options imply there will be data sent or received by the command. The default value is 4096
bytes. LEN cannot exceed 65535 or 0xffff in hexadecimal.
-O, --old
Switch to older style options. Please use as first option.
-P, --page=PG
where PG is the RECEIVE DIAGNOSTIC RESULTS command page code field. If this option is given the
PCV bit in that command is set. When this option is given then no SEND DIAGNOSTIC command is sent
(unlike --list). If PG is 0 then the response is decoded as if it is the SPC Supported Diagnostic
pages diagnostic page. Other PG values (i.e. 1 to 255) have their responses output in hex.
-p, --pf
set Page Format (PF) bit. By default it is clear (i.e. 0) unless the list --list option is given
in which case the Page Format bit is set (as required by SPC-3).
-r, --raw=H,H...
string of comma separated hex numbers each of which should resolve to a byte value (i.e. 0 to ff
inclusive). A (single) space separated string of hex bytes is also allowed but the list needs to
be in quotes. This sequence forms a diagnostic page to be sent with the SCSI SEND DIAGNOSTIC
command. Mostly likely the --pf option should also be given.
-r, --raw=-
reads sequence of bytes from stdin. The sequence may be comma, space, tab or linefeed (newline)
separated. If a line contains "#" then the remaining characters on that line are ignored.
Otherwise each non separator character should resolve to a byte value (i.e. 0 to ff inclusive).
This sequence forms a diagnostic page to be sent with the SCSI SEND DIAGNOSTIC command. Mostly
likely the --pf option should also be given.
-s, --selftest=ST
where ST is the self-test code. The default value is 0 which is inactive. Some other values:
1 : background short self-test
2 : background extended self-test
4 : aborts a (background) self-test that is in progress
5 : foreground short self-test
6 : foreground extended self-test
This option is mutually exclusive with default self-test (i.e. can't have (ST > 0) and --test).
-t, --test
sets the _default_ Self Test (SelfTest) bit. By default this is clear (0). The --selftest=ST
option should not be active together with this option. Both the --doff and/or --uoff options can
be used with this option.
-T, --timeout=SECS
where SECS is a timeout value (in seconds) for foreground self-test operations. The default value
is 7200 seconds (2 hours) and any values of SECS less than the default are ignored.
-u, --uoff
set the Unit Offline (UnitOffL) bit (default is clear). Only significant when --test option is set
for the default self-test. When set other operations on this logical unit may be affected
(delayed) while a default self-test is underway. Some devices (e.g. Fujitsu disks) do more tests
when this bit is set.
-v, --verbose
increase level of verbosity. Can be used multiple times.
-V, --version
print out version string then exit.
NOTES
All devices should support the default self-test. The 'short' self-test codes should complete in 2
minutes or less. The 'extended' self-test codes' maximum duration is vendor specific (e.g. a little over
10 minutes with the author's disks). The foreground self-test codes wait until they are completed while
the background self-test codes return immediately. The results of both foreground and background
self-test codes are placed in the 'self-test results' log page (see sg_logs(8)). The SCSI command timeout
for this utility is set to 60 minutes to allow for slow foreground extended self-tests.
If the DEVICE is a disk then no file systems residing on that disk should be mounted during a foreground
self-test. The reason is that other SCSI commands may become queued behind the foreground self-test and
timeout.
When the --raw=H,H... option is given then self-tests should not be selected. However the --pf (i.e.
"page format") option should be given. The length of the diagnostic page to be sent is derived from the
number of bytes given to the --raw=H,H... option. The diagnostic page code (number) should be the first
byte of the sequence (i.e. as dictated by SPC-3 diagnostic page format). See the EXAMPLES section below.
Arbitrary diagnostic pages can be read (in hex) with the sg_ses(8) utility (not only those defined in
SES-2).
If the utility is used with no options (e.g. "sg_senddiag /dev/sg1") Then a degenerate SCSI SEND
DIAGNOSTIC command is sent with zero in all its fields apart from the opcode. Some devices report this as
an error while others ignore it. It is not entirely clear from SPC-3 if it is invalid to send such a
command.
In the 2.4 series of Linux kernels the DEVICE must be a SCSI generic (sg) device. In the 2.6 series block
devices (e.g. SCSI disks and DVD drives) can also be specified.
To access SCSI enclosures see the sg_ses(8) utility. sg_ses uses the SCSI SEND DIAGNOSTIC and RECEIVE
DIAGNOSTIC RESULTS commands as outlined in the SES-2 (draft) standard.
EXIT STATUS
The exit status of sg_senddiag is 0 when it is successful. Otherwise see the sg3_utils(8) man page.
OLDER COMMAND LINE OPTIONS
The options in this section were the only ones available prior to sg3_utils version 1.23 . Since then
this utility defaults to the newer command line options which can be overridden by using --old (or -O) as
the first option. See the ENVIRONMENT VARIABLES section for another way to force the use of these older
command line options.
-doff set the Device Offline (DevOffL) bit (default is clear). Only significant when -t option is set
for the default self-test. Equivalent to --doff in the main description.
-e outputs the expected extended self-test duration. Equivalent to --extdur in the main description.
-h outputs response from RECEIVE DIAGNOSTIC RESULTS in hex rather than decode it.
-H outputs response from RECEIVE DIAGNOSTIC RESULTS in hex rather than decode it.
-l when a DEVICE is also given lists the names of all diagnostic pages supported by this device. The
request is sent via a SEND DIAGNOSTIC command (with the "pf" bit set) and the response is fetched
by a RECEIVE DIAGNOSTIC RESULTS command. When used in the absence of a DEVICE argument then a list
of diagnostic page names and their numbers, known by this utility, are listed.
-N, --new
Switch to the newer style options.
-pf set Page Format (PF) bit. By default it is clear (i.e. 0) unless the -l option is given in which
case the Page Format bit is set (as required by SPC-3).
-raw=H,H...
string of comma separated hex numbers each of which should resolve to a byte value (i.e. 0 to ff
inclusive). This sequence forms a diagnostic page to be sent with the SCSI SEND DIAGNOSTIC
command. Mostly likely the -pf option should also be given.
-raw=- reads sequence of bytes from stdin. The sequence may be comma, space, tab or linefeed (newline)
separated. If a line contains "#" then the remaining characters on that line are ignored.
Otherwise each non separator character should resolve to a byte value (i.e. 0 to ff inclusive).
This sequence forms a diagnostic page to be sent with the SCSI SEND DIAGNOSTIC command. Mostly
likely the -pf option should also be given.
-s=ST where ST is the self-test code. The default value is 0 which is inactive. A value of 1 selects a
background short self-test; 2 selects a background extended self-test; 5 selects a foreground
short self-test; 6 selects a foreground extended test. A value of 4 will abort a (background)
self-test that is in progress. This option is mutually exclusive with default self-test (i.e. -t).
-t sets the _default_ Self Test (SelfTest) bit. By default this is clear (0). The -s=ST option
should not be active together with this option. Both the -doff and/or -uoff options can be used
with this option.
-T=SECS
where SECS is a timeout value (in seconds) for foreground self-test operations. See the
--timeout=SECS option above.
-uoff set the Unit Offline (UnitOffL) bit (default is clear). Equivalent to --uoff in the main
description.
-v increase level of verbosity. Can be used multiple times.
-V print out version string then exit.
-? output usage message. Ignore all other parameters.
EXAMPLES
The examples sub-directory in the sg3_utils packages contains two example scripts that turn on the CJTPAT
(jitter pattern) on some SAS disks (one script for each phy). One possible invocation for phy 1 is:
sg_senddiag --pf --raw=- /dev/sg2 < sdiag_sas_p1_cjtpat.txt
There is also an example script that turns on the IDLE pattern. Once a test pattern has been started it
can be turned off by resetting the phy or with the STOP phy pattern function:
sg_senddiag --pf --raw=- /dev/sg2 < sdiag_sas_p1_stop.txt
ENVIRONMENT VARIABLES
Since sg3_utils version 1.23 the environment variable SG3_UTILS_OLD_OPTS can be given. When it is present
this utility will expect the older command line options. So the presence of this environment variable is
equivalent to using --old (or -O) as the first command line option.
AUTHOR
Written by Douglas Gilbert
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2003-2018 Douglas Gilbert
This software is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_ses(8), sg_logs(8), smartmontools(see net)
sg3_utils-1.43 May 2018 SG_SENDDIAG(8)