Provided by: fitsh_0.9.4-1_amd64 
NAME
fitrans - performing spatial transformations on the input image
SYNOPSIS
fitrans [transformation and options] <input> [-o|--output <output>]
DESCRIPTION
The main purpose of this program is to perform specific or generic geometric transformations on the input
image.
OPTIONS
General options:
-h, --help
Gives general summary about the command line options.
--long-help, --help-long
Gives a detailed list of command line options.
--wiki-help, --help-wiki, --mediawiki-help, --help-mediawiki
Gives a detailed list of command line options in Mediawiki format.
--version, --version-short, --short-version
Gives some version information about the program.
-i, --input <image file>
Name of the input FITS image file.
-o, --output <image file>
Name of the output FITS image file.
-b, --bitpix <bitpix>
Standard FITS output bitpix value.
-D, --data <spec>
Output pixel data format specification.
Spatial transformations:
-T, --input-transformation <transformation file>
Name of the file which contains the transformation description.Such a file can be created e.g. by
the programs `grtrans` or `grmatch`. This file contains basically the same set of <keyword> =
<value> pairs as it is used after the -t|--transformation option (see there).
-t, --transformation <transformation>
Comma-separated list of parameters for the spatial transformation, see section "Parameters for
spatial transformations" below.
-e, --shift <dx>,<dy>
Imply a transformation that shifts the image by <dx>,<dy>.
--reverse, --inverse
Apply the inverse transformation to the image rather than the original one.
-m Simple linear interpolation between pixels, with no exact flux conservation (just a multiplication
by the Jacobian of the transformation).
-l Linear interpolation between the pixels involving exact flux conservation by integrating on the
image surface.
-c Bicubic spline interpolation between pixels, with no exact flux conservation (just a
multiplication by the Jacobian of the transformation).
-k Interpolation by integrationg the flux on a biquadratic interpolation surface, yielding exact flux
conservation.
-s, --size <sx>,<sy>
The size of the output image if it should differ from the original image size.
-f, --offset <x>,<y>
Zero-point coordinate of the output image in the input image.
Parameters for spatial transformations:
type=<type>
Type of the transformation. In the actual implementation, the only supported type for a
transformation is "polynomial".
order=<order>
Polynomial order for the transformation.
dxfit=<coefficients>
Comma-separated list of the polynomial coefficients for the X coordinate. The number of
coefficients must be 1, 3, 6, ... for the orders 0, 1, 2, ... respectively.
dyfit=<coefficients>
Comma-separated list of the polynomial coefficients for the Y coordinate.
Other simple spatial geometric transformations:
-z, --zoom <factor>, --zoom-xy <x>,<y>
Zoom the image by the given (integer) factor, involving a biquadratic subpixel-level interpolation
and therefore exact flux conservation.
-r, --shrink <factor>, --shrink-xy <x>,<y>
Shrink the image by the given (integer) factor(s).
-d, --median
Use a median-based averaging during the shrinking operation.
-v, --truncated-mean <Nr>
Compute a truncated mean during the shrinking operation by rejecting the <Nr> number of lower and
upper points.
--optimistic-masking
Imply some optimism during the shrinking operation: masked pixels are ignored during the averaging
process and the final mask will be computed in a complement manner.
-g, --magnify <factor>, --magnify-xy <x>,<y>
Same as zooming the image but there is no subpixel-level interpolation.
Large-scale image smoothing:
-a, --smooth <parameters>
Perform a smoothing on the image. The parameters of the smoothing are the following:
spline Do a spline interpolation smoothing
polynomial
Do a polynomial interpolation smoothing
[xy]order=<order>
Spatial order of the smoothing function. The order in the X and Y coordinates can be set
independently, by setting "xorder=..." or "yorder=...".
unity Scale the resulting smoothed image to have a mean of 1.
detrend
The resulting image will be the original image divided by the best fit smoothed surface.
[xy]hsize=<halfsize>
Do a box filtering with the given halfsize.
mean Use the mean value of the pixels for the box filtering.
median Use the median value of the pixels for the box filtering.
iterations=<iterations>
Number of iterations to reject outlier pixels from the box.
lower, upper, sigma=<sigma>
Lower, upper or symmetric rejection level in the units of standard deviation.
Noise estimation:
-n, --noise
Derive an image which reflects the "noise level" of the image.
Slicing or exploding data cube images:
-y, --layer <layer>
Layer (z-axis index) of the desired image slice.
-x, --explode <basename>
Explode the input image into individual planar (two dimensional) FITS image. The basename must
contain at least one printf-like tag of %d, %i, %o, %x or %X that is replaced by the appropriate
layer number index.
-y, --first-layer <n>
Use the specified value for the first layer index. The subsequent layer indices are incremented
normally. By default, the index of the first data cube layer is 0.
Multiple stamp extraction:
-c, --cut <basename>
Extract stamps with a size defined by the -s|--size argument. The stamps are extracted on a grid,
defined by the -p|--step and -w|--count arguments where the stamp grid offset is defined by the
-f|--offset argument. The <basename> should contain two spefic printf-like elements of %x and %y
which are replaced by the corresponding stamp indices in the X and Y directions. In order to have
some sort of pretty-printing in the file names, the %x and %y parts may have the form of %.<N>x
and %.<N>y. Note that despite of the %x convention, both %x and %y are printed in decimal system.
-w, --count <count_x>,<count_y>
Number of stamps to be extracted in X and Y directions, respectively.
-s, --size <sx>,<sy>
The size of the output image stamps.
-p, --step <step_x>,<step_y>
Step size between the stamps in the units of pixels and in the X and Y directions, respectively.
Note that if <step_x> is smaller than <sx> (or similarly, if <step_y> is smaller than <sy>), then
the output stamps will overlap. This might also be intentional for various applications.
-f, --offset <x>,<y>
Zero-point coordinate of the lower-left pixel of the lower-left output stamp (having an index of
%x=0 and %y=0) in the frame of the input image.
REPORTING BUGS
Report bugs to <apal@szofi.net>, see also https://fitsh.net/.
COPYRIGHT
Copyright © 1996, 2002, 2004-2008, 2010-2016, 2018-2020; Pal, Andras <apal@szofi.net>
fitrans 0.9.4 (2021.01.24) January 2021 FITRANS(1)