Provided by: nvme-cli_2.10.2-1_amd64 
NAME
nvme-discover - Send Get Log Page request to Discovery Controller.
SYNOPSIS
nvme discover [--transport=<trtype> | -t <trtype>]
[--nqn=<subnqn> | -n <subnqn>]
[--traddr=<traddr> | -a <traddr>]
[--trsvcid=<trsvcid> | -s <trsvcid>]
[--host-traddr=<traddr> | -w <traddr>]
[--host-iface=<iface> | -f <iface>]
[--hostnqn=<hostnqn> | -q <hostnqn>]
[--hostid=<hostid> | -I <hostid>]
[--raw=<filename> | -r <filename>]
[--device=<device> | -d <device>]
[--config=<filename> | -J <filename>]
[--keep-alive-tmo=<sec> | -k <sec>]
[--reconnect-delay=<#> | -c <#>]
[--ctrl-loss-tmo=<#> | -l <#>]
[--nr-io-queues=<#> | -i <#>]
[--nr-write-queues=<#> | -W <#>]
[--nr-poll-queues=<#> | -P <#>]
[--queue-size=<#> | -Q <#>] [--keyring=<#>]
[--tls_key=<#>] [--hdr-digest | -g] [--data-digest | -G]
[--persistent | -p] [--quiet] [--tls] [--concat]
[--dump-config | -O] [--output-format=<fmt> | -o <fmt>]
[--force] [--nbft] [--no-nbft] [--nbft-path=<STR>]
[--context=<STR>]
[--output-format=<fmt> | -o <fmt>] [--verbose | -v]
DESCRIPTION
Send one or more Get Log Page requests to a NVMe-over-Fabrics Discovery Controller.
If no parameters are given, then nvme discover will attempt to find a /etc/nvme/discovery.conf file to
use to supply a list of Discovery commands to run. If no /etc/nvme/discovery.conf file exists, the
command will quit with an error.
Otherwise, a specific Discovery Controller should be specified using the --transport, --traddr, and if
necessary the --trsvcid flags. A Discovery request will then be sent to the specified Discovery
Controller.
BACKGROUND
The NVMe-over-Fabrics specification defines the concept of a Discovery Controller that an NVMe Host can
query on a fabric network to discover NVMe subsystems contained in NVMe Targets which it can connect to
on the network. The Discovery Controller will return Discovery Log Pages that provide the NVMe Host with
specific information (such as network address and unique subsystem NQN) the NVMe Host can use to issue an
NVMe connect command to connect itself to a storage resource contained in that NVMe subsystem on the NVMe
Target.
Note that the base NVMe specification defines the NQN (NVMe Qualified Name) format which an NVMe endpoint
(device, subsystem, etc) must follow to guarantee a unique name under the NVMe standard. In particular,
the Host NQN uniquely identifies the NVMe Host, and may be used by the Discovery Controller to control
what NVMe Target resources are allocated to the NVMe Host for a connection.
A Discovery Controller has it’s own NQN defined in the NVMe-over-Fabrics specification,
nqn.2014-08.org.nvmexpress.discovery. All Discovery Controllers must use this NQN name. This NQN is used
by default by nvme-cli for the discover command.
OPTIONS
-t <trtype>, --transport=<trtype>
This field specifies the network fabric being used for a NVMe-over-Fabrics network. Current string
values include:
┌───────┬───────────────────────────────────────┐
│ Value │ Definition │
├───────┼───────────────────────────────────────┤
│ rdma │ The network fabric is an rdma network │
│ │ (RoCE, iWARP, Infiniband, basic rdma, │
│ │ etc) │
├───────┼───────────────────────────────────────┤
│ fc │ WIP The network fabric is a Fibre │
│ │ Channel network. │
├───────┼───────────────────────────────────────┤
│ tcp │ The network fabric is a TCP/IP │
│ │ network. │
├───────┼───────────────────────────────────────┤
│ loop │ Connect to a NVMe over Fabrics target │
│ │ on the local host │
└───────┴───────────────────────────────────────┘
-n <subnqn>, --nqn <subnqn>
This field specifies the name for the NVMe subsystem to connect to.
-a <traddr>, --traddr=<traddr>
This field specifies the network address of the Discovery Controller. For transports using IP
addressing (e.g. rdma) this should be an IP-based address (ex. IPv4).
-s <trsvcid>, --trsvcid=<trsvcid>
This field specifies the transport service id. For transports using IP addressing (e.g. rdma) this
field is the port number. By default, the IP port number for the RDMA transport is 4420.
-w <traddr>, --host-traddr=<traddr>
This field specifies the network address used on the host to connect to the Controller. For TCP, this
sets the source address on the socket.
-f <iface>, --host-iface=<iface>
This field specifies the network interface used on the host to connect to the Controller (e.g. IP
eth1, enp2s0, enx78e7d1ea46da). This forces the connection to be made on a specific interface instead
of letting the system decide.
-q <hostnqn>, --hostnqn=<hostnqn>
Overrides the default host NQN that identifies the NVMe Host. If this option is not specified, the
default is read from /etc/nvme/hostnqn first. If that does not exist, the autogenerated NQN value
from the NVMe Host kernel module is used next.
-I <hostid>, --hostid=<hostid>
UUID(Universally Unique Identifier) to be discovered which should be formatted.
-r <filename>, --raw=<filename>
This field will take the output of the nvme discover command and dump it to a raw binary file. By
default nvme discover will dump the output to stdout.
-d <device>, --device=<device>
This field takes a device as input. It must be a persistent device associated with a Discovery
Controller previously created by the command "connect-all" or "discover". <device> follows the format
nvme*, eg. nvme0, nvme1.
-J <filename>, --config=<filename>
Use the specified JSON configuration file instead of the default /etc/nvme/config.json file or none
to not read in an existing configuration file. The JSON configuration file format is documented in
https://github.com/linux-nvme/libnvme/blob/master/doc/config-schema.json
-k <#>, --keep-alive-tmo=<#>
Overrides the default keep alive timeout (in seconds). This option will be ignored for discovery, and
it is only implemented for completeness.
-c <#>, --reconnect-delay=<#>
Overrides the default delay (in seconds) before reconnect is attempted after a connect loss.
-l <#>, --ctrl-loss-tmo=<#>
Overrides the default controller loss timeout period (in seconds).
-i <#>, --nr-io-queues=<#>
Overrides the default number of I/O queues create by the driver. This option will be ignored for the
discovery, and it is only implemented for completeness.
-W <#>, --nr-write-queues=<#>
Adds additional queues that will be used for write I/O.
-P <#>, --nr-poll-queues=<#>
Adds additional queues that will be used for polling latency sensitive I/O.
-Q <#>, --queue-size=<#>
Overrides the default number of elements in the I/O queues created by the driver which can be found
at drivers/nvme/host/fabrics.h. This option will be ignored for the discovery, and it is only
implemented for completeness.
--keyring=<#>
Keyring for TLS key lookup.
--tls_key=<#>
TLS key for the connection (TCP).
-g, --hdr-digest
Generates/verifies header digest (TCP).
-G, --data-digest
Generates/verifies data digest (TCP).
-p, --persistent
Don’t remove the discovery controller after retrieving the discovery log page.
--tls
Enable TLS encryption (TCP).
--concat
Enable secure concatenation (TCP).
--quiet
Suppress already connected errors.
-O, --dump-config
Print out resulting JSON configuration file to stdout.
-o <fmt>, --output-format=<fmt>
Set the reporting format to normal, json or binary. Only one output format can be used at a time.
--force
Disable the built-in persistent discover connection rules. Combined with --persistent flag, always
create new persistent discovery connection.
--nbft
Only look at NBFT tables
--no-nbft
Do not look at NBFT tables
--nbft-path=<STR>
Use a user-defined path to the NBFT tables
--context <STR>
Set the execution context to <STR>. This allows to coordinate the management of the global resources.
-o <fmt>, --output-format=<fmt>
Set the reporting format to normal, json or binary. Only one output format can be used at a time.
-v, --verbose
Increase the information detail in the output.
EXAMPLES
• Query the Discover Controller with IP4 address 192.168.1.3 for all resources allocated for NVMe Host
name host1-rogue-nqn on the RDMA network. Port 4420 is used by default:
# nvme discover --transport=rdma --traddr=192.168.1.3 \
--hostnqn=host1-rogue-nqn
• Issue a nvme discover command using the default system defined NBFT tables:
# nvme discover --nbft
• Issue a nvme discover command with a user-defined path for the NBFT table:
# nvme discover --nbft-path=/sys/firmware/acpi/tables/NBFT1
• Issue a nvme discover command using a /etc/nvme/discovery.conf file:
# Machine default 'nvme discover' commands. Query the
# Discovery Controller's two ports (some resources may only
# be accessible on a single port). Note an official
# nqn (Host) name defined in the NVMe specification is being used
# in this example.
-t rdma -a 192.168.69.33 -s 4420 -q nqn.2014-08.com.example:nvme:nvm-subsystem-sn-d78432
-t rdma -a 192.168.1.4 -s 4420 -q nqn.2014-08.com.example:nvme:nvm-subsystem-sn-d78432
At the prompt type "nvme discover".
SEE ALSO
nvme-connect(1) nvme-connect-all(1)
AUTHORS
This was written by Jay Freyensee[1]
NVME
Part of the nvme-user suite
NOTES
1. Jay Freyensee
mailto:james.p.freyensee@intel.com
NVMe 08/07/2024 NVME-DISCOVER(1)