Ubuntu Manpage: wvdial.conf - wvdial configuration file

NAME

       wvdial.conf - wvdial configuration file

DESCRIPTION

When wvdial starts, it first loads its configuration from /etc/wvdial.conf, which contains basic
information about the modem port, speed, and init string, along with information about your Internet
Service Provider (ISP), such as the phone number, your username, and your password.

The configuration file /etc/wvdial.conf is in Windows "ini" file format, with sections named in square
brackets and a number of variable = value pairs within each section.

Here is a sample configuration file:

[Dialer Defaults]
Modem = /dev/ttyS2
Baud = 57600
Init = ATZ
Init2 = AT S11=50
Phone = 555-4242
Username = apenwarr
Password = my-password

[Dialer phone2]
Phone = 555-4243

[Dialer shh]
Init3 = ATM0

[Dialer pulse]
Dial Command = ATDP

The sample configuration file above contains all of the options necessary to run the two sample command
lines given above. Here is a complete list of settings that wvdial understands:

Modem The location of the device that wvdial should use as your modem. The default is /dev/modem.

Baud The speed at which wvdial will communicate with your modem. The default is 57600 baud.

Init1 ... Init9
wvdial can use up to nine initialization strings to set up your modem. Before dialing, these
strings are sent to the modem in numerical order. These are particularly useful when specifying
multiple sections. See above for an example that uses Init3 to turn the modem's speaker off. The
default is "ATZ" for Init1.

Phone The phone number you want wvdial to dial. You can add up to 4 other phone numbers that wvdial will
dial in order, by adding:

Phone1

Phone2

Phone3

Phone4

Dial Prefix
wvdial will insert this string after the dial command and before the phone number. For example,
to disable call waiting (in North America, anyway) set this to "*70,".

Dial Command
wvdial will use this string to tell the modem to dial. The default is "ATDT".

Login Prompt
If your ISP has an unusual login procedure that wvdial is unable to figure out, you can use this
option to specify a login prompt. When this prompt is received from your ISP, wvdial will send
the Login string.

Password
You must set this to the password you use at your ISP.

Ask Password
By setting this option wvdial will prompt for your password on every dialin. Thus you don't have
to save your password in /etc/wvdial.conf. (Option added by SuSE.)

Password Prompt
If your ISP has an unusual login procedure that wvdial is unable to figure out, you can use this
option to specify a password prompt. When this prompt is received from you ISP, wvdial will send
the Password string.

PPPD Path
If your system has pppd somewhere other than /usr/sbin/pppd, you will need to set this option.

Auto DNS
Try to get the Domain Nameserver (DNS) from the provider. This option is "on" by default.
(Option added by SuSE.)

Check DNS
Check the Domain Nameserver (DNS) after the connection has been set up. This option is "on" by
default. (Option added by SuSE.)

DNS Test1
First DNS lookup for DNS check. (Option added by SuSE.)

DNS Test2
Second DNS lookup for DNS check. (Option added by SuSE.)

Check Def Route
Check the default route after the connection has been set up. This option is "on" by default.
(Option added by SuSE.)

Force Address
This option only applies if you have a static IP address at your ISP, and even then you probably
don't need it. Some ISP's don't send the IP address as part of the PPP negotiation. This option
forces pppd to use the address you give it.

Remote Name
If your ISP uses PAP or CHAP authentication, you might need to change this to your ISP's
authentication name. In most cases, however, it's safe to use the default value, "*".

Carrier Check
wvdial checks your modem during the connection process to ensure that it is actually online. If
you have a weird modem that insists its carrier line is always down, you can disable the carrier
check by setting this option to "no".

Stupid Mode
When wvdial is in Stupid Mode, it does not attempt to interpret any prompts from the terminal
server. It starts pppd immediately after the modem connects. Apparently there are ISP's that
actually give you a login prompt, but work only if you start PPP, rather than logging in. Go
figure. Stupid Mode is (naturally) disabled by default.

New PPPD
You need this option if you have pppd version 2.3.0 or newer, to make wvdial create the file
/etc/ppp/peers/wvdial. This option is enabled by default, thus if you have older pppd you need to
set it to `no' (or upgrade pppd).

Default Reply
When wvdial detects a prompt, and it hasn't seen any clues that indicate what it should send as a
response to the prompt, it defaults to sending "ppp". Sometimes this is inadequate. Use this
option to override wvdial's default prompt response.

Auto Reconnect
If enabled, wvdial will attempt to automatically reestablish a connection if you are randomly
disconnected by the other side. This option is "on" by default.

Idle Seconds
Set the hangup timeout in seconds. If there is inactivity for the given time the connection is
shut down. A hangup timeout of 0 disables this feature.

Abort on Busy
If enabled, wvdial will not retry the connection if the modem says that the line is busy. This
option is "off" by default.

Abort on No Dialtone
If enabled, wvdial will not retry the connection if the modem says that there is no dialtone.
This option is "on" by default.

Dial Attempts
If value is set, wvdial will quit after that many tries .If set to 0, wvdial will happily keep
dialling forever.

Dial Timeout
The maximum time in seconds that wvdial will wait for a connection to be made. Default value is 60
seconds.

The wvdialconf(1) program can be used to detect your modem and fill in the Modem, Baud, and Init/Init2
options automatically.

AUTHORS

       Dave Coombs and Avery Pennarun for Net Integration Technologies Inc.  Great contributions have been  made
       by many people, including SuSE and RedHat. Thanks guys!

NAME

DESCRIPTION

AUTHORS

SEE ALSO