Provided by: libtest-timer-perl_2.12-2_all 
NAME
Test::Timer - test module to test/assert response times
VERSION
The documentation describes version 2.12 of Test::Timer
FEATURES
• Test subroutines to implement unit-tests to time that your code executes before a specified threshold
• Test subroutines to implement unit-tests to time that your code execution exceeds a specified
threshold
• Test subroutine to implement unit-tests to time that your code executes within a specified time frame
• Supports measurements in seconds
• Implements configurable alarm signal handler to make sure that your tests do not execute forever
SYNOPSIS
use Test::Timer;
time_ok( sub { doYourStuffButBeQuickAboutIt(); }, 1, 'threshold of one second');
time_atmost( sub { doYourStuffYouHave10Seconds(); }, 10, 'threshold of 10 seconds');
time_between( sub { doYourStuffYouHave5-10Seconds(); }, 5, 10,
'lower threshold of 5 seconds and upper threshold of 10 seconds');
# Will succeed
time_nok( sub { sleep(2); }, 1, 'threshold of one second');
time_atleast( sub { sleep(2); }, 2, 'threshold of one second');
# Will fail after 5 (threshold) + 2 seconds (default alarm)
time_ok( sub { while(1) { sleep(1); } }, 5, 'threshold of one second');
$test::Timer::alarm = 6 #default 2 seconds
# Will fail after 5 (threshold) + 6 seconds (specified alarm)
time_ok( sub { while(1) { sleep(1); } }, 5, 'threshold of one second');
DESCRIPTION
Test::Timer implements a set of test primitives to test and assert test times from bodies of code.
The key features are subroutines to assert or test the following:
• that a given piece of code does not exceed a specified time limit
• that a given piece of code takes longer than a specified time limit and does not exceed another
EXPORT
Test::Timer exports:
• time_ok
• time_nok
• time_atleast
• time_atmost
• time_between
SUBROUTINES/METHODS
time_ok
Takes the following parameters:
• a reference to a block of code (anonymous sub)
• a threshold specified as a integer indicating a number of seconds
• a string specifying a test name
time_nok( sub { sleep(2); }, 1, 'threshold of one second');
If the execution of the code exceeds the threshold specified the test fail with the following diagnostic
message
Test ran 2 seconds and exceeded specified threshold of 1 seconds
time_nok
The is the inverted variant of time_ok, it passes if the threshold is exceeded and fails if the benchmark
of the code is within the specified timing threshold.
The API is the same as for time_ok.
time_nok( sub { sleep(1); }, 2, 'threshold of two seconds');
If the execution of the code executes below the threshold specified the test fail with the following
diagnostic message
Test ran 1 seconds and did not exceed specified threshold of 2 seconds
time_atmost
This is syntactic sugar for time_ok
time_atmost( sub { doYourStuffButBeQuickAboutIt(); }, 1, 'threshold of one second');
If the execution of the code exceeds the threshold specified the test fail with the following diagnostic
message
Test ran N seconds and exceeded specified threshold of 1 seconds
N will be the actual measured execution time of the specified code
time_atleast
time_atleast( sub { doYourStuffAndTakeYourTimeAboutIt(); }, 1, 'threshold of 1 second');
The test succeeds if the code takes at least the number of seconds specified by the timing threshold.
If the code executes faster, the test fails with the following diagnostic message
Test ran 1 seconds and did not exceed specified threshold of 2 seconds
Please be aware that Test::Timer, breaks the execution with an alarm specified to trigger after the
specified threshold + 2 seconds (default), so if you expect your execution to run longer, set the alarm
accordingly.
$Test::Timer::alarm = $my_alarm_in_seconds;
See also diagnostics.
time_between
This method is a more extensive variant of time_atmost and time_ok, you can specify a lower and upper
threshold, the code has to execute within this interval in order for the test to succeed
time_between( sub { sleep(2); }, 5, 10,
'lower threshold of 5 seconds and upper threshold of 10 seconds');
If the code executes faster than the lower threshold or exceeds the upper threshold, the test fails with
the following diagnostic message
Test ran 2 seconds and did not execute within specified interval 5 - 10 seconds
Or
Test ran 12 seconds and did not execute within specified interval 5 - 10 seconds
PRIVATE FUNCTIONS
_runtest
This is a method to handle the result from _benchmark is initiates the benchmark calling benchmark and
based on whether it is within the provided interval true (1) is returned and if not false (0).
_benchmark
This is the method doing the actual benchmark, if a better method is located this is the place to do the
handy work.
Currently Benchmark is used. An alternative could be Devel::Timer, but I do not know this module very
well and Benchmark is core, so this is used for now.
The method takes two parameters:
• a code block via a code reference
• a threshold (the upper threshold, since this is added to the default alarm
import
Test::Builder required import to do some import hokus-pokus for the test methods exported from
Test::Timer. Please refer to the documentation in Test::Builder
DIAGNOSTICS
All tests either fail or succeed, but a few exceptions are implemented, these are listed below.
• Test did not exceed specified threshold, this message is diagnosis for time_atleast and time_nok
tests, which do not exceed their specified threshold
• Test exceeded specified threshold, this message is a diagnostic for time_atmost and time_ok, if the
specified threshold is surpassed.
This is the key point of the module, either your code is too slow and you should address this or your
threshold is too low, in which case you can set it a bit higher and run the test again.
• Test did not execute within specified interval, this is the diagnostic from time_between, it is the
diagnosis if the execution of the code is not between the specified lower and upper thresholds
• Insufficient parameters, this is the message if a specified test is not provided with the sufficient
number of parameters, consult this documentation and correct accordingly
• Execution exceeded threshold and timed out, the exception is thrown if the execution of tested code
exceeds even the alarm, which is default 2 seconds, but can be set by the user or is equal to the
upper threshold + 2 seconds
The exception results in a diagnostic for the failing test. This is a fail-safe to avoid that code
runs forever. If you get this diagnose either your code is too slow and you should address this or it
might be error prone. If this is not the case adjust the alarm setting to suit your situation.
CONFIGURATION AND ENVIRONMENT
This module requires no special configuration or environment.
Tests are sensitive and be configured using environment and configuration files, please see the section
on test and quality.
DEPENDENCIES
• Carp
• Benchmark
• Error
• Test::Builder
• Test::Builder::Module
INCOMPATIBILITIES
This module holds no known incompatibilities.
BUGS AND LIMITATIONS
This module holds no known bugs.
The current implementations only use seconds and resolutions should be higher, so the current
implementation is limited to seconds as the highest resolution.
On occasion failing tests with CPAN-testers have been observed. This seem to be related to the test-suite
being not taking into account that some smoke-testers do not prioritize resources for the test run and
that additional processes/jobs are running. The test-suite have been adjusted to accommodate this but
these issues might reoccur.
TEST AND QUALITY
Coverage report for the release described in this documentation (see VERSION).
---------------------------- ------ ------ ------ ------ ------ ------ ------
File stmt bran cond sub pod time total
---------------------------- ------ ------ ------ ------ ------ ------ ------
blib/lib/Test/Timer.pm 100.0 100.0 100.0 100.0 100.0 99.9 100.0
...Timer/TimeoutException.pm 100.0 n/a n/a 100.0 100.0 0.0 100.0
Total 100.0 100.0 100.0 100.0 100.0 100.0 100.0
---------------------------- ------ ------ ------ ------ ------ ------ ------
The Test::Perl::Critic test runs with severity 5 (gentle) for now, please refer to t/critic.t and
t/perlcriticrc.
Set TEST_POD to enable Test::Pod test in t/pod.t and Test::Pod::Coverage test in t/pod-coverage.t.
Set TEST_CRITIC to enable Test::Perl::Critic test in t/critic.t
CONTINUOUS INTEGRATION
This distribution uses Travis for continuous integration testing, the Travis reports are public
available.
SEE ALSO
• Test::Benchmark
ISSUE REPORTING
Please report any bugs or feature requests using GitHub
• GitHub Issues <https://github.com/jonasbn/perl-test-timer/issues>
SUPPORT
You can find (this) documentation for this module with the "perldoc" command.
perldoc Test::Timer
You can also look for information at:
• Homepage <https://jonasbn.github.io/perl-test-timer/>
• MetaCPAN <https://metacpan.org/pod/Test-Timer>
• AnnoCPAN: Annotated CPAN documentation <http://annocpan.org/dist/Test-Timer>
• CPAN Ratings <http://cpanratings.perl.org/d/Test-Timer>
DEVELOPMENT
• GitHub Repository <https://github.com/jonasbn/perl-test-timer>, please see the guidelines for
contributing <https://github.com/jonasbn/perl-test-timer/blob/master/CONTRIBUTING.md>.
AUTHOR
• Jonas Bromso (jonasbn) "<jonasbn at cpan.org>"
ACKNOWLEDGEMENTS
• Mohammad S Anwar (MANWAR), POD corrections PRs #23
• Erik Johansen (UNIEJO), suggestion for clearing alarm
• Gregor Herrmann (GREGOA) from the Debian Perl Group, PR #16 fixes to spelling mistakes
• Nigel Horne (NHORNE), issue #15 suggestion for better assertion in time_atleast
• Nigel Horne (NHORNE), issue #10/#12 suggestion for improvement to diagnostics
• p-alik, PR #4 eliminating warnings during test
• Kent Fredric (KENTNL), PR #7 addressing file permissions
• Nick Morrott, PR #5 corrections to POD
• Bartosz Jakubski, reporting issue #3
• Gabor Szabo (SZABGAB), suggestion for specification of interval thresholds even though this was
obsoleted by the later introduced time_between
• Paul Leonerd Evans (PEVANS), suggestions for time_atleast and time_atmost and the handling of
$SIG{ALRM}. Also bug report for addressing issue with Debian packaging resulting in release 0.10
• brian d foy (BDFOY), for patch to _runtest
LICENSE AND COPYRIGHT
Test::Timer and related modules are (C) by Jonas Bromso (jonasbn) 2007-2021
Test::Timer and related modules are released under the Artistic License 2.0
Used distributions are under copyright of there respective authors and designated licenses
Image used on website <https://jonasbn.github.io/perl-test-timer/> is under copyright by Veri Ivanova
<https://unsplash.com/photos/p3Pj7jOYvnM>
perl v5.36.0 2022-10-13 Test::Timer(3pm)