Ubuntu Manpage: thinkfan - A simple fan control program

Provided by: thinkfan_1.3.1-4build1_amd64

NAME

       thinkfan - A simple fan control program

SYNOPSIS

       thinkfan [-hnqDd] [-b BIAS] [-c CONFIG] [-s SECONDS] [-p [DELAY]]

DESCRIPTION

Thinkfan sets the fan speed according to temperature limits set in the config file. It can read
temperatures from a number of sources:

/proc/acpi/ibm/thermal
Which is provided by the thinkpad_acpi kernel module on older Thinkpads,

temp*_input files in sysfs
Which may be provided by any hwmon drivers, including thinkpad_acpi on modern Thinkpads,

Hard disks with S.M.A.R.T. support
With the help of libatasmart, if thinkfan was compiled with -DUSE_ATASMART=ON

From the proprietary nVidia driver
When the proprietary nVidia driver is used, no hwmon for the card will be available. In this
situation, thinkfan can use the proprietary NVML API to get temperatures.

The fan can be /proc/acpi/ibm/fan or some PWM file in /sys/class/hwmon. See thinkfan.conf(5) for a
detailed explanation of the config syntax.

WARNING: This program does only very basic sanity checking on the configuration. That means that you can
set your temperature limits as insane as you like.

There are two general modes of operation:

COMPLEX MODE
In complex mode, temperature limits are defined for each sensor thinkfan knows about. Setting suitable
limits for each sensor in your system will probably require a bit of experimentation and good knowledge
about your hardware, but it's the safest way of keeping each component within its specified temperature
range. See http://www.thinkwiki.org/wiki/Thermal_Sensors for details on which sensor measures what
temperature in a Thinkpad. On other systems you'll have to find out on your own. See the example configs
to learn about the syntax.

SIMPLE MODE
In simple mode, Thinkfan uses only the highest temperature found in the system. That may be dangerous,
e.g. for hard disks. That's why you should provide a correction value (i.e. add 10-15 °C) for the sensor
that has the temperature of your hard disk (or battery...). See the example config files for details
about that.

CONFIGURATION

       Some example configurations are provided with the source package. For a detailed see the config man  page
       thinkfan.conf(5).

OPTIONS

-h Show a short help message

-s SECONDS
Maximum seconds between temperature updates (default: 5)

-b BIAS
Floating point number (-10 to 30) to control rising temperature exaggeration. If the temperature
increases by more than 2 °C during one cycle, this number is used to calculate a bias, which is
added to the current highest temperature seen in the system:

current_tmax = current_tmax + delta_t * BIAS / 10

This means that negative numbers can be used to even out short and sudden temperature spikes like
those seen on some on-DIE sensors. Use DANGEROUS mode to remove the -10 to +30 limit. Note that
you can't have a space between -b and a negative argument, because otherwise getopt will interpret
things like -10 as an option and fail (i.e. write -b-10 instead of -b -10).

Default is 15.0

-c FILE
Load a different configuration file. By default, thinkfan first tries to load /etc/thinkfan.yaml,
and /etc/thinkfan.conf after that. The former must be in YAML format, while the latter can be
either YAML or the old legacy syntax.

If this option is specified, thinkfan attempts to load the config only from FILE. If its name
ends in “.yaml”, it must be in YAML format. Otherwise, it can be either YAML or legacy syntax.
See thinkfan.conf(5) and thinkfan.conf.legacy(5) for details.

-n Do not become a daemon and log to terminal instead of syslog

-q Be quiet, i.e. reduce logging level from the default. Can be specified multiple times until only
errors are displayed/logged.

-v Be more verbose. Can be specified multiple times until every message is displayed/logged.

-p [SECONDS]
Use the pulsing-fan workaround (for older Thinkpads). Takes an optional floating-point argument
(0-10s) as depulsing duration. Default 0.5s.

-d Do not read temperature from sleeping disks. Instead, 0 °C is used as that disk's temperature.
This is needed if reading the temperature causes your disk to wake up unnecessarily. NOTE: This
option is only available if thinkfan was built with -D USE_ATASMART.

-D DANGEROUS mode: Disable all sanity checks. May damage your hardware!!

SIGNALS

       SIGINT and SIGTERM simply interrupt operation and should cause thinkfan to terminate cleanly.

       SIGHUP makes thinkfan reload its config. If there's any problem with the new config, we keep the old one.

       SIGUSR1 causes thinkfan to dump all currently known temperatures either to syslog, or to the console  (if
       running with the -n option).

RETURN VALUE

       0      Normal exit

       1      Runtime error

       2      Unexpected runtime error

       3      Invalid commandline option

BUGS

       If thinkfan tells you to, or if you feel like it, report issues at the Github issue tracker:

       https://github.com/vmatare/thinkfan/issues

thinkfan 1.3.1                                    December 2021                                      THINKFAN(1)