Provided by: ipv6toolkit_2.0+ds.1-2build2_amd64 
NAME
nI6 - A security assessment tool for attack vectors based on ICMPv6 Node Information messages
SYNOPSIS
ni6 [-i INTERFACE] [-S LINK_SRC_ADDR | -R] [-D LINK_DST_ADDR] [-s SRC_ADDR[/LEN] | -r] [-d DST_ADDR] [-c
HOP_LIMIT] [-y FRAG_SIZE] [-u DST_OPT_HDR_SIZE] [-U DST_OPT_U_HDR_SIZE] [-H HBH_OPT_HDR_SIZE] [-P SIZE |
-6 IPV6_ADDR | -4 IPV4_ADDR | -n NAME | -N LEN | -x LEN -o TYPE] [-Z SIZE] [-e] [-C ICMP6_CODE] [-q
NI_QTYPE] [-X NI_FLAGS] [-P SIZE | -w IPV6_ADDR | -W IPV4_ADDR | -a NAME | -A LEN | -Q LEN -O TYPE] [-E]
[-j PREFIX[/LEN]] [-k PREFIX[/LEN]] [-J LINK_ADDR] [-K LINK_ADDR] [-b PREFIX[/LEN]] [-g PREFIX[/LEN]] [-B
LINK_ADDR] [-G LINK_ADDR] [-L | -l] [-z] [-v] [-h]
DESCRIPTION
ni6 allows the assessment of IPv6 implementations with respect to a variety of attack vectors based on
ICMPv6 Node Information messages. This tool is part of the SI6 Networks' IPv6 Toolkit: a security
assessment suite for the IPv6 protocols.
This tool has two modes of operation: "active" and "listening". In "active" mode, the tool attacks a
specific target, while in "listening" mode the tool listens to ICMPv6 Node Information Query messages on
the local network, and sends ICMPv6 Node Information Reply messages in response to such traffic. Active
mode is employed if an IPv6 Destination Address is specified. Listening mode is employed if the "-L"
option (or its long counterpart "--listen") is set. If both an attack target and the "-L" option are
specified, the attack is launched against the specified target, and then the tool enters listening mode
to respond incoming packets with TCP segments.
The tool supports filtering of incoming packets based on the Ethernet Source Address, the Ethernet
Destination Address, the IPv6 Source Address, and the IPv6 Destination Address. There are two types of
filters: "block filters" and "accept filters". If any "block filter" is specified, and the incoming
packet matches any of those filters, the message is discarded (and thus no ICMPv6 NI Reply messages are
sent in response). If any "accept filter" is specified, incoming packets must match any of the specified
"accept filters" in order for the tool to respond with ICMPv6 NI Reply messages.
OPTIONS
ni6 takes it parameters as command-line options. Each of the options can be specified with a short name
(one character preceded with the hyphen character, as e.g. "-i") or with a long name (a string preceded
with two hyphen characters, as e.g. "--interface").
ni6 supports IPv6 Extension Headers, including the IPv6 Fragmentation Header, which might be of use to
circumvent layer-2 filtering and/or Network Intrusion Detection Systems (NIDS). However, IPv6 extension
headers are not employed by default, and must be explicitly enabled with the corresponding options.
-i INTERFACE, --interface INTERFACE
This option specifies the network interface that the tool will use. If the destination address
("-d" option) is a link-local address, or the "listening" ("-L") mode is selected, the interface
must be explicitly specified. The interface may also be specified along with a destination
address, with the "-d" option.
-s SRC_ADDR, --src-address SRC_ADDR
This option specifies the IPv6 source address (or IPv6 prefix) to be used for the Source Address
of the attack packets. If an IPv6 prefix is specified, the IPv6 Source Address of the ICMPv6
packets will be randomized from the specified prefix.
Note: When operating in "listening" mode, the Source Address is automatically selected depending
on the IPv6 Destination Address of the ICMPv6 NI Query (unless a specific IPv6 Source Address has
been specified with the "-s" option).
-d DST_ADDR, --dst-address DST_ADDR
This option specifies the IPv6 Destination Address of the victim. It can be left unspecified only
if the "-L" option is selected (i.e., if the tool is to operate in "listening" mode).
Note: When operating in "listening" mode, the Destination Address is automatically set to the
Source Address of the incoming ICMPv6 NI Query message.
--hop-limit, -A
This option specifies the Hop Limit to be used for the IPv6 packets. It is randomized by default.
-y SIZE, --frag-hdr SIZE
This option specifies that the resulting packet must be fragmented. The fragment size must be
specified as an argument to this option.
-u HDR_SIZE, --dst-opt-hdr HDR_SIZE
This option specifies that a Destination Options header is to be included in the resulting packet.
The extension header size must be specified as an argument to this option (the header is filled
with padding options). Multiple Destination Options headers may be specified by means of multiple
"-u" options.
-U HDR_SIZE, --dst-opt-u-hdr HDR_SIZE
This option specifies a Destination Options header to be included in the "unfragmentable part" of
the resulting packet. The header size must be specified as an argument to this option (the header
is filled with padding options). Multiple Destination Options headers may be specified by means of
multiple "-U" options. This option is only valid if the "-y" option is specified (as the concept
of "unfragmentable part" only makes sense when fragmentation is employed).
-H HDR_SIZE, --hbh-opt-hdr HDR_SIZE
This option specifies that a Hop-by-Hop Options header is to be included in the resulting packet.
The header size must be specified as an argument to this option (the header is filled with padding
options). Multiple Hop-by-Hop Options headers may be specified by means of multiple "-H" options.
-S SRC_LINK_ADDR, --src-link-address SRC_LINK_ADDR
This option specifies the link-layer Source Address of the TCP segments. If left unspecified, the
link-layer Source Address is set to the real link-layer address of the network interface.
-D DST_LINK_ADDR, --dst-link-address DST_LINK_ADDR
This option specifies the link-layer Destination Address of the ICMPv6 NI packets. By default, the
link-layer Destination Address is automatically set to the link-layer address of the destination
host (for on-link destinations) or to the link-layer of the first-hop router.
--payload-size, -P
This options specifies the size (in bytes) of the ICMPv6 NI payload.
--subject-ipv6, -6
This option specifies an IPv6 Address to be used as the Subject of ICMPv6 Node Information Query
messages.
--subject-ipv4, -4
This option specifies an IPv4 Address to be used as the Subject of ICMPv6 Node Information Query
messages.
--subject-name, -n
This option specifies a Name to be used as the Subject of ICMPv6 Node Information Query messages.
By default, the specified name is considered to be a Fully-Qualified Domain Name (FQDN). Please
consult the "--sname-slabel" option for instructions on how to specify "single-label" names.
--subject-fname, -N
This option instructs the ni6 tool to set the Subject of ICMPv6 NI Query messages to a forged
name of the specified length.
Note: The forged name is a sequence of labels of 'a' characters, with the maximum label size being
specified by means of the "--max-label-size" option.
--subject-ename, -x
This option instructs the ni6 tool to set the Subject of an ICMPv6 NI Query message to a malformed
label of the specified length. This option is useful for including a malformed label that "spans
past the end of the ICMPv6 NI Query".
--subject-nloop, -O
This option specifies that the Data field should be set to a Name that contains a DNS compression
loop. The loop type is specified with this option, with valid values being in the range 0-1.
--sname-slabel, -e
This option specifies that the specified Subject Name is a single-label name, and hence should be
terminated with two (rather than one) NULL labels.
--max-label-size, -Z
This option specifies the maximum Name label size. It defaults to 63.
--code, -C
This option specified the ICMPv6 code. For ICMPv6 NI Query messages, if specific Subject type is
specified, the ICMPv6 code is automatically set to the corresponding value.
--qtype, -q
This option specifies the Qtype value of ICMPv6 NI messages. For ICMPv6 NI Reply messages, if
specific Data type is specified, the ICMPv6 Qtype is automatically set to the corresponding value.
--flags, -X
This option specified the "Flags" field of the ICMPv6 NI messages.
For ICMPv6 NI Query messages of Qtype 3 (Node IPv6 Addresses), the "Flags" field defaults to
"GSLCA". For ICMPv6 NI Query messages of Qtype 4 (Node IPv4 Addresses), the "Flags" field defaults
to "A". For other ICMPv6 NI Query messages it defaults to 0. For ICMPv6 Reply messages, the
"Flags" field is copied from the corresponding ICMPv6 NI Query message.
--data-ipv6, -w
This option specifies an IPv6 Address to be used as the Data of ICMPv6 Node Information Reply
messages.
--data-ipv4, -W
This option specifies an IPv4 Address to be used as the Data of ICMPv6 Node Information Reply
messages.
--data-name, -a
This option specifies a Name to be used as the Data of ICMPv6 Node Information Reply messages. By
default, the specified name is considered to be a Fully-Qualified Domain Name (FQDN). Please
consult the "--dname-slabel" option for instructions on how to specify "single-label" names.
--data-fname, -A
This option instructs the ni6 tool to set the Data of the ICMPv6 NI Reply messages to a forged
name of the specified length.
Note: The forged name is a sequence of labels of 'a' characters, with the maximum label size being
specified by means of the "--max-label-size" option.
--data-ename, -Q
This option instructs the ni6 tool to set the Data of ICMPv6 NI Reply messages to a malformed
label of the specified length. This option is useful for including a malformed label that "spans
past the end of the ICMPv6 NI Reply".
--data-nloop, -O
This option specifies that the Data field should be set to a Name that contains a DNS compression
loop. The loop type is specified with this option, with valid values being in the range 0-2.
--dname-slabel, -E
This option specifies that the specified Data Name is a single-label name, and hence should be
terminated with two (rather than one) NULL labels.
-j SRC_ADDR, --block-src SRC_ADDR
This option sets a block filter for the incoming packets, based on their IPv6 Source Address. It
allows the specification of an IPv6 prefix in the form "-j prefix/prefixlen". If the prefix length
is not specified, a prefix length of "/128" is selected (i.e., the option assumes that a single
IPv6 address, rather than an IPv6 prefix, has been specified).
-k DST_ADDR, --block-dst DST_ADDR
This option sets a block filter for the incoming Neighbor Solicitation messages, based on their
IPv6 Destination Address. It allows the specification of an IPv6 prefix in the form "-k
prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128" is selected
(i.e., the option assumes that a single IPv6 address, rather than an IPv6 prefix, has been
specified).
-J SRC_ADDR, --block-link-src SRC_ADDR
This option sets a block filter for the incoming packets, based on their link-layer Source
Address. The option must be followed by a link-layer address (this option is only valid for
Ethernet interfaces).
-K DST_ADDR, --block-link-dst DST_ADDR
This option sets a block filter for the incoming packets, based on their link-layer Destination
Address. The option must be followed by a link-layer address (this option is only valid for
Ethernet interfaces).
-b SRC_ADDR, --accept-src SRC_ADDR
This option sets an accept filter for the incoming packets, based on their IPv6 Source Address. It
allows the specification of an IPv6 prefix in the form "-b prefix/prefixlen". If the prefix length
is not specified, a prefix length of "/128" is selected (i.e., the option assumes that a single
IPv6 address, rather than an IPv6 prefix, has been specified).
-g DST_ADDR, --accept-dst DST_ADDR
This option sets a accept filter for the incoming packets, based on their IPv6 Destination
Address. It allows the specification of an IPv6 prefix in the form "-g prefix/prefixlen". If the
prefix length is not specified, a prefix length of "/128" is selected (i.e., the option assumes
that a single IPv6 address, rather than an IPv6 prefix, has been specified).
-B SRC_ADDR, --accept-link-src SRC_ADDR
This option sets an accept filter for the incoming Neighbor Solicitation messages, based on their
link-layer Source Address. The option must be followed by a link-layer address (this option is
only valid for Ethernet interfaces).
-G DST_ADDR, --accept-link-dst DST_ADDR
This option sets an accept filter for the incoming packets, based on their link-layer Destination
Address. The option must be followed by a link-layer address (this option is only valid for
Ethernet interfaces).
--forge-src-addr, -r
This option instructs the ni6 tool to forge the IPv6 Source Address of ICMPv6 NI messages. Note
that when operating in listening mode, unless this tool is set, ni6 will not impersonate other
nodes.
--forge-link-src-addr, -R
This option instructs the ni6 tool to forge the link-layer Source Address of ICMPv6 NI messages.
Note: Some interface cards (or their corresponding drivers) may silently discard packets that
contain a forged link-layer Source Address.
--loop, -l
This option instructs the tcp6 tool to send periodic TCP segments to the victim node. The amount
of time to pause between sending TCP segments can be specified by means of the "-z" option, and
defaults to 1 second. Note that this option cannot be set in conjunction with the "-L"
("--listen") option.
--sleep, -z
This option specifies the amount of time to pause between sending ICMPv6 Node Information Query
messages (when the "--loop" option is set). If left unspecified, it defaults to 1 second.
--listen, -L
This instructs the ni6 tool to operate in listening mode (possibly after attacking a specified
target). Note that this option cannot be used in conjunction with the "-l" ("--loop") option.
--verbose, -v
This option instructs the ni6 tool to be verbose. When the option is set twice, the tool is "very
verbose", and the tool also informs which packets have been discarded as a result of applying the
specified filters.
--help, -h
Print help information for the ni6 tool.
EXAMPLES
The following sections illustrate typical use cases of the ni6 tool.
Example #1
# ni6 -i eth0 --subject-ipv6 ff02::1 -d ff02::1 -q 2 -v
Send an ICMPv6 Node Information Query to the multicast address ff02::1 ("-d" option), with a Subject IPv6
Address of "ff02::1" ("--subject-ipv6" option), querying for Node names ("-q" option). Be verbose.
Example #2
# ni6 -i eth0 --data-fname 1000 -L --forge-src-addr -v
Listen to incoming ICMPv6 Node Information Query messages querying for node names, and respond with
ICMPv6 NI Reply messages that contain a forged name of 700 bytes. Forge the IPv6 Source Address of the
packets. Be verbose.
AUTHOR
The ni6 tool and the corresponding manual pages were produced by Fernando Gont <fgont@si6networks.com>
for SI6 Networks <http://www.si6networks.com>.
COPYRIGHT
Copyright (c) 2011-2013 Fernando Gont.
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free
Documentation License, Version 1.3 or any later version published by the Free Software Foundation; with
no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is available
at <http://www.gnu.org/licenses/fdl.html>.
NI6(1)