Provided by: mrtg_2.17.10-12_amd64 
NAME
cfgmaker - Creates mrtg.cfg files (for mrtg-2.17.10)
SYNOPSIS
cfgmaker [options] [community@]router [[options] [community@]router ...]
OPTIONS
--ifref=name interface references by Interface Name (default)
--ifref=ip ... by Ip Address
--ifref=eth ... by Ethernet Number
--ifref=descr ... by Interface Description
--ifref=nr ... by Interface Number
--ifref=type ... by Interface Type
You may also use multiple options separated by commas,
in which case the first available one is used:
e.g. --ifref=ip,name,nr
--ifdesc=nr interface description uses Interface Number (default)
--ifdesc=ip ... uses Ip Address
--ifdesc=eth ... uses Ethernet Number
--ifdesc=descr ... uses Interface Description
--ifdesc=name ... uses Interface Name
--ifdesc=catname ... uses CatOS Interface Name
--ifdesc=ppname ... uses Passport Port Name
--ifdesc=alias ... uses Interface Alias
--ifdesc=type ... uses Interface Type
You may also use multiple options separated by commas,
in which case the first available one is used:
e.g. --ifdesc=catname,ppname,descr,alias,ip,name,nr
--if-filter=f Test every interface against filter f to decide whether
or not to include that interface into the collection.
Currently f is being evaluated as a Perl expression
and it's truth value is used to reject or accept the
interface.
(Experimental, under development, might change)
--if-template=templatefile
Replace the normal target entries for the interfaces
with an entry as specified by the contents in the file
templatefile. The file is supposed to contain Perl
code to be executed to generate the lines for the
target in the configuration file.
(Experimental, under development, might change)
--host-template=templatefile
In addition to creating targets for a host's interfaces
do also create targets for the host itself as specified
by the contents in the file templatefile. The file is
supposed to contain Perl code to be executed to generate
the lines for the host related targets (such as CPU,
ping response time measurements etc.) in the config-
uration file.
(Experimental, under development, might change)
--global "x: a" add global config entries
--nodefaultglobal do not include default global settings
--no-down do not look at admin or opr status of interfaces
--show-op-down show interfaces which are operatively down
--zero-speed=spd use this speed in bits-per-second as the interface
speed for all interfaces that return a speed of 0
via ifSpeed/ifHighSpeed. 100Mbps = 100000000
--subdirs=format give each router its own subdirectory, naming each per
"format", in which HOSTNAME and SNMPNAME will be
replaced by the values of those items -- for instance,
--subdirs=HOSTNAME or --subdirs="HOSTNAME (SNMPNAME)"
--noreversedns do not reverse lookup ip numbers
--community=cmty Set the default community string to "cmty" instead of
"public".
--enable-ipv6 Enable IPv6 support, if the required libraries are
present. Numeric IPv6 addresses must be enclosed
in square brackets, e.g. public@[2001:760:4::1]:161
--use-16bit Use 16bit SNMP request IDs to query all routers.
--snmp-options=:[<port>][:[<tmout>][:[<retr>][:[<backoff>][:<ver>]]]]
Specify default SNMP options to be appended to all
routers following. Individual fields can be empty.
Routers following might override some or all of the
options given to --snmp-options.
--dns-domain=domain
Specifies a domain to append to the name of all
routers following.
--nointerfaces Don't do generate any configuration lines for interfaces,
skip the step of gathering interface information and
don't run any interface template code.
--interfaces Generate configuration lines for interfaces (this is the
default). The main purpose of this option is to negate
an --nointerfaces appearing earlier on the command line.
--help brief help message
--man full documentation
--version print the version of cfgmaker
--output=file output filename default is STDOUT
DESCRIPTION
Cfgmaker creates MRTG configuration files based on information pulled from a router or another SNMP
manageable device.
[community@]router
Community is the community name of the device you want to create a configuration for. If not specified,
it defaults to 'public'; you might want to try this first if you do not know the community name of a
device. If you are using the wrong community name you will get no response from the device.
Router is the DNS name or the IP number of an SNMP-manageable device. Following the name you can specify
6 further options separated by colons. The full syntax looks like this:
router[:[prt][:[tmout][:[retr][:[backoff][:vers]]]]]
Of special interest may be the last parameter, vers. If you set this to '2' then your device will be
queried with SNMP version 2 requests. This allows you to poll the 64 bit traffic counters in the device
and will thus work much better with fast interfaces (no more counter overrun). Note that the order in
which the routers are specified on the command line do matter as the same order is used when the
configuration file is generated. The first specified router has it's configuration lines generated
first, followed by the lines belonging to the next router and so on.
Note that the first line of the generated cfg file will contain all the commandline options you used for
generating it. This is to allow for the easy 'regeneration' in case you want to add newhosts or make some
other global change.
Configuration
Except for the --output and --global options, all options affect only the routers following them on the
command line. If an option specified earlier on the command line reappears later on the command line
with another value, the new value overrides the old value as far as remaining routers are concerned.
This way options might be tailored for groups of routers or for individual routers.
See --output and --global for how their behaviour is affected by where or how many times they appear on
the command line.
See the Examples below on how to set an option differently for multiple routers.
--help
Print a brief help message and exit.
--man
Prints the manual page and exits.
--version
Print the version of cfgmaker. This should match the version of MRTG for which config files are
being created.
--ifref nr|ip|eth|descr|name
Select the interface identification method. Default is nr which identifies the router interfaces by
their number. Unfortunately the interface numbering scheme in an SNMP tree can change. Some routers
change their numbering when new interfaces are added, others change their numbering every full moon
just for fun.
To work around this sad problem MRTG can identify interfaces by 4 other properties. None of these
works for all interfaces, but you should be able to find one which does fine for you. Note that
especially ethernet addresses can be problematic as some routers have the same ethernet address on
most of their interface cards.
Select ip to identify the interface by its IP number. Use eth to use the ethernet address for
identification. Use descr to use the Interface description. Or use name to use the Interface name.
You can specify multiple properties if you wish, separated by commas. In this case, cfgmaker will
use the first item in the list which can provide unique identification. This allows you to specify,
for example, to use IP address and to use ifName if this is not defined:
--ifref ip,name
If your chosen method does not allow unique interface identification on the device you are querying,
cfgmaker will tell you about it.
--ifdesc nr|ip|eth|descr|name|type|alias
Select what to use as the description of the interface. The description appears in the "Title[]"
property for the target as well as the text header in the HTML code defined in the target's
"PageTop[]". Default is to use nr which is just the interface number which isn't always useful to
the viewer of the graphs.
There are 6 other properties which could be used. Use ip if you want to use the interface's IP-
address. Use eth if you want to use the interface's ethernet address. If you want a better
description, you can use either descr, name or alias. Exactly what each of these do varies between
different equipment so you might need to experiment. For instance, for a serial interface on a Cisco
router running IOS using name might result in "S0" being the interface description , descr might
result in "Serial0" and alias might result in "Link to HQ" (provided that is what is used as the
interface's "description" in the router's configuration).
Finally, if you want to describe the interface by it's Btype (i.e "ethernetCSMA", "propPointtoPoint"
etc) you can use type.
You can specify multiple properties if you wish, separated by commas. In this case, cfgmaker will
use the first item in the list which is available for this interface. This allows you to specify,
for example, to use any of the different aliases in order of preference.
--if-filter 'filter-expression'
First of all, this is under some development and is experimental.
Use this if you want to have better control over what interfaces gets included into the
configuration. The filter-expression is evaluated as a piece of Perl code and is expected to return
a truth value. If true, include the interface and if false, exclude the interface.
For a further discussion on how these filters work, see the section "Details on Filters" below.
--if-template template-file
First of all, this is under some development and is experimental.
Use this if you want to control what the line for each target should look like in the configuration
file. The contents of the file template-file will be evaluated as a Perl program which generates the
lines using certain variables for input and output.
For a further discussion on how these templates work, see the section "Details on Templates" below.
--host-template template-file
First of all, this is under some development and is experimental.
Use this if you want to have some extra targets related to the host itself such as CPU utilization,
ping response time to the host, number of busy modems etc. The contents of the file template-file
will be evaluated once per host as a Perl program which generates the lines using certain variables
for input and output.
For a further discussion on how these templates work, see the section "Details on Templates" below.
--community community-string
Use this to set the community for the routers following on the command line to community-string.
Individual routers might override this community string by using the syntax community@router.
--enable-ipv6
This option enables IPv6 support. It requires the appropriate perl modules; if they are not found
then IPv6 is disabled (see the ipv6 documentation).
cfgmaker will use IPv6 or IPv4 depending on the target. If the target is a numeric address, the
protocol depends on the type of address. If the target is a hostname, cfgmaker will try to resolve
the name first to an IPv6 address then to an IPv4 address.
IPv6 numeric addresses must be specified between square braces.
For example:
cfgmaker --enable-ipv6 [2001:760:4::1]:165:::2
If the target has both an IPv6 address and an IPv4 address with the same hostname, cfgmaker first
queries the target using IPv6 and falls back to IPv4 if it fails. This is useful for targets which
don't support SNMP over IPv6.
--use-16bit
This option forces the use of 16bit SNMP request IDs. Some broken SNMP agents do not accept 32bit
request IDs. Try to avoid this option as much as possible, complain to your agent vendor instead.
--snmp-options :[port][:[timeout][:[retries][:[backoff][:version]]]]
Use this to set the default SNMP options for all routers following on the command line. Individual
values might be omitted as well as trailing colons. Note that routers might override individual (or
all) values specified by --snmp-options by using the syntax
router[:[port][:[timeout][:[retries][:[backoff][:version]]]]]
--global "bla: abc"
Use this to add global options to the generated config file. You can call --global several times to
add multiple options. The line will appear in the configuration just before the config for the next
router appearing on the command line.
--global "workdir: /home/mrtg"
If you want some default Options you might want to put
--global "options[_]: growright,bits"
Specifying --global after the last router on the command line will create a line in the configuration
file which will appear after all the routers.
--noreversedns
Do not try to reverse lookup IP numbers ... a must for DNS free environments.
--no-down
Normally cfgmaker will not include interfaces which are marked anything but administratively and
operationally UP. With this switch you get them all.
--show-op-down
Include interfaces which are operatively down.
--zero-speed speed
Assign this speed in bits-per-second to all interfaces which return 0 for ifSpeed and ifHighSpeed.
Some switches, notably Foundry equipment, return a speed of zero for some interfaces. For example,
to have all interfaces reporting zero set to 100Mbps, use --zero-speed=100000000.
--subdirs format
Give each router its own subdirectory for the HTML and graphics (or .rrd) files. The directory name
is the given format string with a couple of pattern replacements. The string "HOSTNAME" will be
replaced by the hostname of the router (however you specified it on the cfgmaker commandline -- it
may be an actual hostname or just an IP address), and "SNMPNAME" will be replaced with the device's
idea of its own name (the same name that appears on the right side of the "Title" lines). For
instance, a call like:
cfgmaker --subdirs=HOSTNAME__SNMPNAME public@10.10.0.18
would result in the generation of lines looking something like:
Directory[10.10.0.18_1]: 10.10.0.18__fp2200-bothrip-1.3
--output file
Write the output from cfgmaker into the file file. The default is to use "STDOUT". --output is
expected to appear only once on the command line. If used multiple times, the file specified by the
last --output will be used.
--nointerfaces
Don't generate configuration lines for interfaces.
This makes cfgmaker skip all steps related to interfaces which means it will not do any polling of
the router to retrieve interface information which speeds up the execution of cfgmaker and it will
neither run any interface templates.
--interfaces
This makes cfgmaker generate configuration lines for interfaces (the default behaviour).
The main usage of this option is to negate an --nointerfaces appearing earlier on the command line.
SNMP V3 Options
Cfgmaker supports SNMP V3 using the Net:SNMP perl module. There are optional parameters affecting SNMP
operation.
--enablesnmpv3 {yes|no}
The --enablesnmpv3 option is an optional flag to check for the presence of the Net::SNMP libraries.
Cfgmaker will try to determine whether this flag is required and will set the values automatically.
SNMPv3 Arguments
A SNMP context is a collection of management information accessible by a SNMP entity. An item of
management information may exist in more than one context and a SNMP entity potentially has access to
many contexts. The combination of a contextEngineID and a contextName unambiguously identifies a context
within an administrative domain. In a SNMPv3 message, the contextEngineID and contextName are included
as part of the scopedPDU. All methods that generate a SNMP message optionally take a --contextengineid
and --contextname argument to configure these fields.
Context Engine ID
The --contextengineid argument expects a hexadecimal string representing the desired contextEngineID.
The string must be 10 to 64 characters (5 to 32 octets) long and can be prefixed with an optional
"0x". Once the --contextengineid is specified it stays with the object until it is changed again or
reset to default by passing in the undefined value. By default, the contextEngineID is set to match
the authoritativeEngineID of the authoritative SNMP engine.
Context Name
The contextName is passed as a string which must be 0 to 32 octets in length using the --contextname
argument. The contextName stays with the object until it is changed. The contextName defaults to an
empty string which represents the "default" context.
User-based Security Model Arguments
The User-based Security Model (USM) used by SNMPv3 requires that a securityName be specified using the
--username argument. The creation of a Net::SNMP object with the version set to SNMPv3 will fail if the
--username argument is not present. The --username argument expects a string 1 to 32 octets in length.
Different levels of security are allowed by the User-based Security Model which address authentication
and privacy concerns. A SNMPv3 target will derive the security level (securityLevel) based on which of
the following arguments are specified.
By default a securityLevel of 'noAuthNoPriv' is assumed. If the --authkey or --authpassword arguments
are specified, the securityLevel becomes 'authNoPriv'. The --authpassword argument expects a string
which is at least 1 octet in length. Optionally, the --authkey argument can be used so that a plain text
password does not have to be specified in a script. The --authkey argument expects a hexadecimal string
produced by localizing the password with the authoritativeEngineID for the specific destination device.
The "snmpkey" utility included with the Net::SNMP distribution can be used to create the hexadecimal
string (see snmpkey).
Two different hash algorithms are defined by SNMPv3 which can be used by the Security Model for
authentication. These algorithms are HMAC-MD5-96 "MD5" (RFC 1321) and HMAC-SHA-96 "SHA-1" (NIST FIPS PUB
180-1). The default algorithm used by the module is HMAC-MD5-96. This behavior can be changed by using
the --authprotocol argument. This argument expects either the string 'md5' or 'sha' to be passed to
modify the hash algorithm.
By specifying the arguments --privkey or --privpassword the securityLevel associated with the object
becomes 'authPriv'. According to SNMPv3, privacy requires the use of authentication. Therefore, if
either of these two arguments are present and the --authkey or --authpassword arguments are missing, the
creation of the object fails. The --privkey and --privpassword arguments expect the same input as the
--authkey and --authpassword arguments respectively.
The User-based Security Model described in RFC 3414 defines a single encryption protocol to be used for
privacy. This protocol, CBC-DES "DES" (NIST FIPS PUB 46-1), is used by default or if the string 'des' is
passed to the --privprotocol argument. By working with the Extended Security Options Consortium
http://www.snmp.com/eso/, the module also supports additional protocols which have been defined in draft
specifications. The draft http://www.snmp.com/eso/draft-reeder-snmpv3-usm-3desede-00.txt defines the
support of CBC-3DES-EDE "Triple-DES" (NIST FIPS 46-3) in the User-based Security Model. This protocol
can be selected using the --privprotocol argument with the string '3desede'. The draft
http://www.snmp.com/eso/draft-blumenthal-aes-usm-04.txt describes the use of CFB128-AES-128/192/256 "AES"
(NIST FIPS PUB 197) in the USM. The three AES encryption protocols, differentiated by their key sizes,
can be selected by passing 'aescfb128', 'aescfb192', or 'aescfb256' to the -privprotocol argument.
Details on Filters
The purpose of the filters is to decide which interfaces to accept and which interfaces to reject. This
decision is done for each interface by evaluating the filter expression as a piece of Perl code and
investigating the result of the evaluation. If true, accept the interface otherwise reject it.
When working with filters, remember that Perl has it's own idea of what truth and false is. The empty
string "" and the string "0" are false, all other strings are true. This further implies that any
integer value of 0 is false as well as any undef value. It also implies that all references are
considered true.
As the filter is evaluated as a Perl expression, several useful constructs in Perl are worth mentioning:
Expressions might be grouped by using parentheses "()". Expressions might be combined using boolean
operators such as the following:
"and" (equivalent with "&&")
Boolean "and" of the two expressions, is only true if both expressions are true. Example:
expression1 and expression2
"or" (equivalent with "||")
Boolean "or" of the two expressions, is true if either or both expressions are true. Example:
expression1 or expression2
"not" (equivalent with "!")
Boolean negation of a single expression. Example: not expression . Yet another example:
!expression
(For more details on this I recommend a book on Perl)
Predefined Filter Variables
To facilitate, there are a number of predefined values available to use in the filter. Note that these
variables are also available when templates interfaces are evaluated (but not host templates).
Caveat: All these variables' names begin with a dollar sign ($), which is a syntactic requirement for
scalar variables in Perl. The danger here is that the dollar sign in many shells is an active character
(often used for shell variables exactly as in Perl variables) so it is important to ensure that the Perl
expression isn't evaluated by the command line shell as shell code before being passed to cfgmaker as
command line arguments. In shells like Bourne shell, ksh shell or bash shell, placing the entire
expression within single quotes will avoid such accidental evaluation:
'--if-filter=($default_iftype && $if_admin)'
$if_type
This is an integer specifying the interface type as per the SNMP standards and as reported by the
polled device. A complete list of interface types would be impractical for this document , but there
are a number predefined variables below. Normally, cfgmaker puts in the target's PageTop this iftype
value within parenthesis after the name of the interface type. (e.g "propPointToPointSerial (22)").
Here's a list of some of the most common interface types by number:
6 ethernetCsmacd
7 iso88023Csmacd
9 iso88025TokenRing
15 fddi
19 E1
20 basicISDN
21 primaryISDN
22 propPointToPointSerial
23 ppp
24 softwareLoopback
30 ds3
32 frame-relay
33 rs232
37 atm
39 sonet
44 frameRelayService
46 hssi
49 aal5
53 propVirtual
62 Fast Ethernet (100BaseT)
63 ISDN & X.25
69 Full Duplex Fast Ethernet (100BaseFX)
94 Asymmetric Digital Subscriber Loop (ADSL)
117 Gigabit Ethernet
134 ATM Sub Interface
$default
True if and only if cfgmaker normally should accepted the interface based on the interfaces
administrative and operational state (taking the flags --no-down and --show-op-down into account) and
it's type (and a few other things).
$default_ifstate
True if and only if cfgmaker would have accepted the interface based on it's operational and
administrative states (also taking into account the presence of the flags --no-down and
--show-op-down).
$default_iftype
True if and only if cfgmaker would have accepted the interface based on it's type (and a few type
specific details in addition).
$if_admin
True if and only if the interface is in an administrative up state.
$if_oper
True if and only if the interface is in an operational up state.
A number of variables are also predefined to easily decide if an interface belong to a certain category
or not. Below is all those variables listed together with which if_type numbers each variable will be
true for. Note that some variables refer to other variables as well.
$if_is_ethernet
True for ethernet interfaces (nr 6, 7, 26, 62, 69 and 117).
$if_is_isdn
True for various ISDN interface types (nr 20, 21, 63, 75, 76 and 77)
$if_is_dialup
True for dial-up interfaces such as PPP as well as ISDN. (nr 23, 81, 82 and 108 in addition to the
numbers of $if_is_isdn).
$if_is_atm
True for miscellaneous ATM related interface types (nr 37, 49, 107, 105, 106, 114 and 134).
$if_is_wan
True for WAN interfaces point to point, Frame Relay and High Speed Serial ( 22,32,44,46)
$if_is_lan
True for LAN interfaces (8, 9, 11, 15, 26, 55, 59, 60 and 115 in addition to the numbers of
$if_is_ethernet).
$if_is_dsl
True for ADSL, RDSL, HDSL and SDSL (nr 94, 95, 96, 97)
$if_is_loopback
True for software loopback interfaces (nr 24)
$if_is_ciscovlan
True for Cisco VLAN interfaces (interfaces with the word Vlan or VLAN in their ifdescs)
$if_vlan_id
Returns the vlan id associated with a specific port on Cisco Catalyst switches under both Catalyst OS
and IOS, and 3Com switches. If it is not a vlan interface, will return undef.
$if_cisco_trunk
Returns the trunking state of a specific port on Cisco Catalyst switches under both Catalyst OS and
IOS. Returns "1" if the interface is a trunk, undef otherwise.
$if_MTU
Returns the Maximum Transfer Unit associated with a specific port.
Besides that, you can also use the variables defined for templates below. Further, all the variables
available in cfgmaker is at the scripts disposal even if the use of such features is discouraged. More
"shortcuts" in the form of variables and functions will be made available in the future instead.
Examples on Filters
The following filter will not affect which interfaces gets included or excluded, it will make cfgmaker
behave as normally.
'--if-filter=$default'
The following filter will make cfgmaker exclude PPP (23) interfaces:
'--if-filter=$default && $if_type!=23'
The following filter will make cfgmaker behave as usual except that it will consider the operational
state of an interface irrelevant but still reject all interfaces which are administratively down.
'--if-filter=$if_admin && $default_iftype'
Details on Templates
The contents of the template files are evaluated as a Perl program. A number or Perl variables are
available for the program to read and others are used to be written to.
As quite a few of the predefined variables has values which are are supposed to be used in HTML code some
of them have an "HTML-escaped" variant, e.g $html_syslocation is the HTML escaped variant of
$syslocation. The HTML escaping means that the chars "<", ">" and "&" are replaced by "<", ">" and
"&" and that newlines embedded in the string are prepended with "<BR>" and appended with a space
character (if a newline is last in the string it is not touched).
Writable Template Variables
These are the variables available to store the configuration lines in. Some of them are initialized
prior to the evaluation of the template but such content normally is comments for inclusion in the final
configuration file so those variables might be reset to the empty string in the template code to
eliminate the comments. The other way around is also possible, the contents of these variables might be
extended with further information for various reasons such as debugging etc.
Once the template has been evaluated, the following happens: if the template is a interface template and
the actual interface for some reason is rejected and thus needs to be commented out, all the lines in the
variable $target_lines are turned into comments by adding a hash mark ("#") at their beginning. Then all
the variables $head_lines, $problem_lines , $target_lines and $separator_lines are concatenated together
to form the lines to add to the configuration file.
$target_lines
This variable is the placeholder for the configuration lines created by the template. $target_lines
is predefined to be empty when the template code is evaluated.
$head_lines
This variable is intended to be the placeholder for the comment line appearing just before the target
in the configuration file. It is initialized with that comment line before the evaluation of the
template code and if the template doesn't modify $head_lines during evaluation, the comment will look
like usual in the config file.
$problem_lines
This variable is intended to be the placholder for the comment lines describing any problems which
might have been encountered when trying to add the target into the configuration. For host templates
it's normally not used and for those it's predefined as the empty string. For interface templates
$problem_lines is predefined with the error description comments which cfgmaker normally would use
for rejected interfaces or as the empty string for accepted interfaces.
It is possible to test against $problem_lines to find out if an interface will be included or
rejected but this is not recommended. Test against $if_ok instead.
$separator_lines
This variable is the placeholder for the string to use as the separator between the code for
individual targets. The contents of this variable is put after each target (so the lines will appear
after the end of the last target in the config as well).
Predefined Template Variables
All the variables below are available for interface templates to use. For host templates, only those
listed under "Host and System Variables" are available.
For interface templates the variables listed under "Predefined Filter Variables" are also available.
Host and System Variables
$router_name
This is the fully qualified name for the router. It is affected by the following items on the
command line: the router name itself and --dns-domain.
$router_connect
This is the reference string for the router being polled. It is on the form community@router
possibly followed by some snmp options. It is affected by the following items on the command line:
the router name itself, --community, --snmp-options and --dns-domain. (There's no HTML escaped
variant available)
$directory_name
This variable should contain the directory name as cfgmaker normally would use as the value for the
"Directory[]" directive. The value is determined by the --subdirs command line option. If --subdirs
isn't specified $directory_name will be the empty string. (There's no HTML escaped variant
available)
$syscontact
This variable is the router's SNMP sysContact value. (HTML escaped variant: $html_syscontact)
$sysname
This variable is the router's SNMP sysName value. (No HTML escaped variant available)
$syslocation
This variable is the router's SNMP sysLocation value. (HTML escaped variant: $html_syslocation)
$sysdescr
This variable is the router's SNMP sysDescr value. It is normally not used by cfgmaker but might be
useful in a template. (HTML escaped variant: $html_sysdescr)
Interface Target Related Variables
$target_name
This is what cfgmaker normally would use as the the name of the target. The target name is what is
found within the square brackets, "[]", for target directives. (There's no HTML escaped variant
available)
$if_ref
This the reference string for the interface. It is expected to be used in the "Target[xyz]"
directive to distinguish what interface to use. The value of this variable is affected by the
--ifref command line option. It is normally used together with $router_connect. (There's no HTML
escaped variant available)
$if_ok
This variable is true if the interface is going to be included into the configuration file, otherwise
false. Don't test against other variables such as $problem_lines to find out if an interface will be
rejected or not, use this $if_ok instead.
$default_target_lines
This variable contains all the target lines which cfgmaker by default outputs for this interface.
It's useful if you want to have the "standard target" but want to add some extra lines to it by using
a template.
By default cfgmaker uses the following directives for each target it generates: Target[], SetEnv[],
MaxBytes[], Title[], PageTop[] and if there is any directory specified also the Directory[] directive.
To facilitate the creation of templates which generates target configs which are similar to the default
one, each of the above mentioned directive lines have a corresponding variable containing the line as
cfgmaker would have output it by default.
Note that none of these have a HTML escaped variant, text in them is HTML escaped where needed. Also
note that they do not have any newline at the end.
$default_target_directive
This variable contains the default string for the Target[] directive line.
$default_setenv_directive
This variable contains the default string for the SetEnv[] directive line.
$default_directory_directive
This variable contains the default string for the Directory[] directive line which means it is an
empty string (with no newline) if there's no directory.
$default_maxbytes_directive
This variable contains the default string for the MaxBytes[] directive line.
$default_title_directive
This variable contains the default string for the Title[] directive line.
$default_pagetop_directive
This variable contains the default string for the PageTop[] directive lines.
Interface Network Configuration Variables
$if_ip
This variable should contain the IP-address of the interface, if any has been assigned to it.
(There's no HTML escaped variant available)
$ifindex
This variable is the SNMP ifIndex for the interface which per definition always is an integer.
(There's no HTML escaped variant available)
$if_index
Equivalent with $ifindex.
$if_eth
Contains the ethernet address of the interface, if any. (There's no HTML escaped variant available)
$if_speed
This variable is the speed in bytes/second (with prefixes). (There's no HTML escaped variant
available)
$if_speed_str
This variable is a cooked speed description which is either in bits or bytes depending on whether or
not the bits option is active and also with the proper prefix for the speed (k, M, G etc). (No HTML
escaped variant available)
$if_type_desc
This variable is a textual description of the interface type. (HTML escaped variant:
$html_if_type_desc)
$if_type_num
This variable the integer value corresponding to the interface type (for a listing for the value for
the more common interface types, see the section DETAILS ON FILTERS above). (No HTML escaped variant
available)
$if_dns_name
This is the DNS name for the interface. (No HTML escaped variant available)
Interface Name, Description and Alias Variables
It might seem confusing with both Name, Description and Alias in this context and to some extent it is.
Name and Description are usually supported on most equipment but how they are used varies, both between
manufacturers as well as between different categories of equipment from the same manufacturer. The Alias
is at least supported by Cisco IOS, and that variable contains whatever is used in the IOS statement
called "description" for the interface (not to be confused with the SNMP variables for Description).
For better control from the command line consider $if_title_desc which contents are controlled by the
--if-descr command line option.
$if_snmp_descr
This variable should contain the "raw" description of the interface as determined by the SNMP polling
of the router. (HTML escaped variant: $html_if_snmp_descr)
$if_snmp_name
The "raw" name for the interface as provided by SNMP polling. (HTML escaped variant:
$html_if_snmp_name)
$if_snmp_alias
The "raw" ifAlias for the interface as provided by SNMP polling. (HTML escaped variant:
$html_if_snmp_alias)
$if_cisco_descr
The "raw" CiscolocIfDescr for the interface as provided by SNMP polling. (HTML escaped variant:
$html_if_cisco_descr)
$if_description
This is the "cooked" description string for the interface, taking into account the SNMP values found
for the interface's RDescr, ifAlias and CiscolocIfDescr. (HTML escaped variant:
$html_if_description)
$if_title
The full string cfgmaker by default would have used for the Title[] directive in the configuration as
well as the content of the topmost H1 tag in the PageTop[]. Is composed by the contents of
$desc_prefix, $if_title_desc and $sysname.
As $if_title depends on $if_title_desc, it is possible to indirectly control $if_title by using the
command line option --if-descr.
(HTML escaped variant: $html_if_title)
$if_port_name
If the host is a Cisco Catalyst LAN switch, this variable is the name of that port. (No HTML escaped
variant available)
$if_pp_port_name
If the host is a Nortel Passport LAN switch, this variable is the name of that port. (No HTML
escaped variant available)
$desc_prefix
This variable is a prefix of the description of what the target is to use in the "Title[]" directive
and in the H1 section of the "PageTop[]". Default is "Traffic analysis for ". (HTML escaped
variant: $html_desc_prefix)
$if_title_desc
This is the description of the interface normally used by cfgmaker as part of the variable $if_title.
The latter is used as the full string in the "Title[]" directive and the H1 section in the PageTop[].
$if_title_desc is controlled by the command line option --if-descr which indirectly controls the
contents of $if_title
(HTML escaped variant: $html_if_title_desc)
Help Functions for Templates
The following functions exists to facilitate the writing of host and interface templates.
html_escape(string)
html_escape() takes a string as an argument and returns a new string where the following
substitutions has been done: the chars "<", ">" and "&" are replaced by "<", ">" and "&"
and that newlines embedded in the string are prepended with "<BR>" and appended with a space
character (newlines at the end of the string are not touched).
oid_pick($router_connect,$v3opt,"oid1","oid2"...)
This function will try to poll each of the oids specified until it is successful or has run out of
oids. It will return the name of the first oid that worked or undef if it is not successful
Example Template Files
Template Example 1: Eliminating Rejected Targets From Appearing
This template file generates exactly the same configuration code per interface as cfgmaker does by
default, with the exception that it eliminates all lines (comments as well as config code) for an
interface if the interface happens to be rejected.
if(not $problem_lines)
{
$target_lines .= <<ECHO;
Target[$target_name]: $if_ref:$router_connect
SetEnv[$target_name]: MRTG_INT_IP="$if_ip" MRTG_INT_DESCR="$if_snmp_descr"
ECHO
if ($directory_name) {
$target_lines .= "Directory[$target_name]: $directory_name\n";
}
$target_lines .= <<ECHO;
MaxBytes[$target_name]: $if_speed
Title[$target_name]: $html_desc_prefix$html_if_title_desc -- $sysname
PageTop[$target_name]: <h1>$html_desc_prefix$html_if_title_desc -- $sysname</h1>
<div id="sysdetails">
<table>
<tr>
<td>System:</td>
<td>$sysname in $html_syslocation</td>
</tr>
<tr>
<td>Maintainer:</td>
<td>$html_syscontact</td>
</tr>
<tr>
<td>Description:</td>
<td>$html_if_description</td>
</tr>
<tr>
<td>ifType:</td>
<td>$html_if_type_desc ($if_type_num)</td>
</tr>
<tr>
<td>ifName:</td>
<td>$html_if_snmp_name</td>
</tr>
ECHO
$target_lines .= <<ECHO if defined $if_port_name;
<tr>
<td>Port Name:</td>
<td>$if_port_name</td>
</tr>
ECHO
$target_lines .= <<ECHO if defined $if_pp_port_name;
<tr>
<td>Port Name:</td>
<td>$if_pp_port_name</td>
</tr>
ECHO
$target_lines .= <<ECHO;
<tr>
<td>Max Speed:</td>
<td>$if_speed_str</td>
</tr>
ECHO
$target_lines .= <<ECHO if $if_ip;
<tr>
<td>Ip:</td>
<td>$if_ip ($if_dns_name)</td>
</tr>
ECHO
$target_lines .= <<ECHO;
</table>
</div>
ECHO
} else {
$head_lines="";
$problem_lines="";
$target_lines="";
$separator_lines="";
}
Template Example 2: Simpler Version of Example 1
Example 1 was partly intended to demonstrate how to customize the generation of interface targets but
also to provide a hint of how the variables are used in the "default" template which one could consider
that cfgmaker normally uses.
If you're only interested in the easiest way of entirely eliminating those reject interfaces, the
template below would do the job as well by using $default_target_lines.
if($if_ok) {
$target_lines = $default_target_lines;
} else {
$head_lines="";
$problem_lines="";
$target_lines="";
$separator_lines="";
}
Template Example 3: Creating CPU Targets for Hosts
Below is an example of a host template.
$head_lines .= <<ECHO;
#---------------------------------------------------------------------
ECHO
my $target_name = $router_name . ".cpu";
$target_lines .= <<ECHO;
YLegend[$target_name]: Percentage CPU load
ShortLegend[$target_name]: %
Legend1[$target_name]: CPU load in %
Legend2[$target_name]:
Legend3[$target_name]: Max Observed CPU load
Legend4[$target_name]:
LegendI[$target_name]: CPU Load:
LegendO[$target_name]:
WithPeak[$target_name]: ywm
MaxBytes[$target_name]: 100
Options[$target_name]: growright, gauge, nopercent
Title[$target_name]: $router_name CPU load
Target[$target_name]: 1.3.6.1.4.1.9.2.1.58.0&1.3.6.1.4.1.9.2.1.58.0:$router_connect
PageTop[$target_name]: <h1>$router_name CPU load</h1>
<div>
<table>
<tr>
<td>System:</td>
<td>$router_name in $html_syslocation</td>
</tr>
<tr>
<td>Maintainer:</td>
<td>$html_syscontact</td>
</tr>
<tr>
<td>Description:</td>
<td>$html_sysdescr</td>
</tr>
<tr>
<td>Resource:</td>
<td>CPU.</td>
</tr>
</table>
</div>
ECHO
EXAMPLES
The first example creates a config file for router.place.xyz: the router has the community name public.
Interfaces get identified by their IP number. Two global options get added to the config file. The
config file gets redirected to mrtg.conf. The '\' signs at the end of the line mean that this command
should be written on a single line.
cfgmaker --global "WorkDir: /home/tobi" \
--global "Options[_]: growright,bits" \
--ifref=ip \
public@router.place.xyz > mrtg.cfg
Note: if cfgmaker is not in your path, but you are in the directory where cfgmaker is stored, you can
start it with ./cfgmaker
The next example creates a config file for four devices: router1.place.xyz, router2.place.xyz,
switch1.place.xyz and switch2.place.xyz all with the community public.
The two routers will have --ifref set to descr whilst the two switches will use --ifref set to name.
Further the routers will use --ifdesc set to alias and switch1.place.xyz will use --ifdesc set to descr
whilst switch2.place.xyz use name instead.
Finally, there will be two Options lines inserted in the configuration: One will be in the beginning,
whilst the other will be inserted after the lines related to the two routers but before those lines
related to the switches.
cfgmaker --global "WorkDir: /home/tobi" \
--global "Options[_]: growright,bits" \
--ifref=descr \
--ifdesc=alias \
public@router1.place.xyz \
public@router2.place.xyz \
--global "Options[_]: growright" \
--ifref=name \
--ifdesc=descr \
public@switch1.place.xyz \
--ifdesc=name \
public@switch2.place.xyz > mrtg.cfg
The next example demonstrates how to use the --community, --snmp-options and --dns-domain to make the
command line simpler. All the equipment will use the community hidden, except for the ppp-server which
use community access. All equipment uses these SNMP options: 1s timeout, 1 retry and SNMP version 2
(backoff and port is unspecified which means they use the default values). The exception again is the
ppp-server which uses SNMP version 1. Finally, all the equipment is part of the domain place.xyz, except
for the ppp-server which is part of the domain remote.place.xyz. Note that the latter is achieved simply
by specifying the name of the ppp-server to be ppp-server.remote .
cfgmaker --global "WorkDir: /home/tobi" \
--global "Options[_]: growright,bits" \
--dns-domain=place.xyz \
--community=hidden \
--snmp-options=::1:1::2 \
router1 \
router2 \
router3 \
router4 \
router5 \
switch1 \
switch2 \
switch3 \
switch4 \
switch5 \
switch6 \
switch7 \
access@ppp-server.remote:::::1 > mrtg.cfg
SEE ALSO
mrtg-reference
AUTHOR
Tobias Oetiker <tobi@oetiker.ch> and Jakob Ilves <jakob.ilves@oracle.com>
LICENSE
GNU General Public License
COPYRIGHT
Cfgmaker is Copyright 2000 by Tobias Oetiker <tobi@oetiker.ch>
2.17.10 2022-01-19 CFGMAKER(1)