Provided by: freebsd-manpages_12.2-1_all 
NAME
uart — driver for Universal Asynchronous Receiver/Transmitter (UART) devices
SYNOPSIS
device uart
device puc
device uart
device scc
device uart
In /boot/device.hints:
hint.uart.0.disabled="1"
hint.uart.0.baud="38400"
hint.uart.0.port="0x3f8"
hint.uart.0.flags="0x10"
With flags encoded as:
0x00010 device is potential system console
0x00080 use this port for remote kernel debugging
0x00100 set RX FIFO trigger level to ``low'' (NS8250 only)
0x00200 set RX FIFO trigger level to ``medium low'' (NS8250 only)
0x00400 set RX FIFO trigger level to ``medium high'' (default, NS8250 only)
0x00800 set RX FIFO trigger level to ``high'' (NS8250 only)
DESCRIPTION
The uart device driver provides support for various classes of UARTs implementing the EIA RS-232C (CCITT
V.24) serial communications interface. Each such interface is controlled by a separate and independent
instance of the uart driver. The primary support for devices that contain multiple serial interfaces or
that contain other functionality besides one or more serial interfaces is provided by the puc(4), or
scc(4) device drivers. However, the serial interfaces of those devices that are managed by the puc(4),
or scc(4) driver are each independently controlled by the uart driver. As such, the puc(4), or scc(4)
driver provides umbrella functionality for the uart driver and hides the complexities that are inherent
when elementary components are packaged together.
The uart driver has a modular design to allow it to be used on differing hardware and for various
purposes. In the following sections the components are discussed in detail. Options are described in
the section that covers the component to which each option applies.
CORE COMPONENT
At the heart of the uart driver is the core component. It contains the bus attachments and the low-level
interrupt handler.
HARDWARE DRIVERS
The core component and the kernel interfaces talk to the hardware through the hardware interface. This
interface serves as an abstraction of the hardware and allows varying UARTs to be used for serial
communications.
SYSTEM DEVICES
System devices are UARTs that have a special purpose by way of hardware design or software setup. For
example, Sun UltraSparc machines use UARTs as their keyboard interface. Such an UART cannot be used for
general purpose communications. Likewise, when the kernel is configured for a serial console, the
corresponding UART will in turn be a system device so that the kernel can output boot messages early on
in the boot process.
KERNEL INTERFACES
The last but not least of the components is the kernel interface. This component ultimately determines
how the UART is made visible to the kernel in particular and to users in general. The default kernel
interface is the TTY interface. This allows the UART to be used for terminals, modems and serial line IP
applications. System devices, with the notable exception of serial consoles, generally have specialized
kernel interfaces.
HARDWARE
The uart driver supports the following classes of UARTs:
• NS8250: standard hardware based on the 8250, 16450, 16550, 16650, 16750 or the 16950 UARTs.
• SCC: serial communications controllers supported by the scc(4) device driver.
Pulse Per Second (PPS) Timing Interface
The uart driver can capture PPS timing information as defined in RFC 2783. The API, accessed via
ioctl(2), is available on the tty device. To use the PPS capture feature with ntpd(8), symlink the tty
callout device /dev/cuau? to /dev/pps0.
The hw.uart.pps_mode tunable configures the PPS capture mode for all uart devices; it can be set in
loader.conf(5). The dev.uart.0.pps_mode sysctl configures the PPS capture mode for a specific uart
device; it can be set in loader.conf(5) or sysctl.conf(5).
The following capture modes are available:
0x00 Capture disabled.
0x01 Capture pulses on the CTS line.
0x02 Capture pulses on the DCD line.
The following values may be ORed with the capture mode to configure capture processing options:
0x10 Invert the pulse (RS-232 logic low = ASSERT, high = CLEAR).
0x20 Attempt to capture narrow pulses.
Add the narrow pulse option when the incoming PPS pulse width is small enough to prevent reliable capture
in normal mode. In narrow mode the driver uses the hardware's ability to latch a line state change; not
all hardware has this capability. The hardware latch provides a reliable indication that a pulse
occurred, but prevents distinguishing between the CLEAR and ASSERT edges of the pulse. For each detected
pulse, the driver synthesizes both an ASSERT and a CLEAR event, using the same timestamp for each. To
prevent spurious events when the hardware is intermittently able to see both edges of a pulse, the driver
will not generate a new pair of events within a half second of the prior pair. Both normal and narrow
pulse modes work with ntpd(8).
Add the invert option when the connection to the uart device uses TTL level signals, or when the PPS
source emits inverted pulses. RFC 2783 defines an ASSERT event as a higher-voltage line level, and a
CLEAR event as a lower-voltage line level, in the context of the RS-232 protocol. The modem control
signals on a TTL-level connection are typically inverted from the RS-232 levels. For example, carrier
presence is indicated by a high signal on an RS-232 DCD line, and by a low signal on a TTL DCD line.
This is due to the use of inverting line driver buffers to convert between TTL and RS-232 line levels in
most hardware designs. Generally speaking, a connection to a DB-9 style connector is an RS-232 level
signal at up to 12 volts. A connection to header pins or an edge-connector on an embedded board is
typically a TTL signal at 3.3 or 5 volts.
Special Devices
The uart driver also supports an initial-state and a lock-state control device for each of the callin and
the callout "data" devices. The termios settings of a data device are copied from those of the
corresponding initial-state device on first opens and are not inherited from previous opens. Use stty(1)
in the normal way on the initial-state devices to program initial termios states suitable for your setup.
The lock termios state acts as flags to disable changing the termios state. E.g., to lock a flag
variable such as CRTSCTS, use stty crtscts on the lock-state device. Speeds and special characters may
be locked by setting the corresponding value in the lock-state device to any nonzero value. E.g., to
lock a speed to 115200, use “stty 115200” on the initial-state device and “stty 1” on the lock-state
device.
Correct programs talking to correctly wired external devices work with almost arbitrary initial states
and almost no locking, but other setups may benefit from changing some of the default initial state and
locking the state. In particular, the initial states for non (POSIX) standard flags should be set to
suit the devices attached and may need to be locked to prevent buggy programs from changing them. E.g.,
CRTSCTS should be locked on for devices that support RTS/CTS handshaking at all times and off for devices
that do not support it at all. CLOCAL should be locked on for devices that do not support carrier.
HUPCL may be locked off if you do not want to hang up for some reason. In general, very bad things
happen if something is locked to the wrong state, and things should not be locked for devices that
support more than one setting. The CLOCAL flag on callin ports should be locked off for logins to avoid
certain security holes, but this needs to be done by getty if the callin port is used for anything else.
DEPRECATION NOTICE
The PC Card attachment of this driver is scheduled for removal prior to the release of FreeBSD 13.0
FILES
/dev/ttyu? for callin ports
/dev/ttyu?.init
/dev/ttyu?.lock corresponding callin initial-state and lock-state devices
/dev/cuau? for callout ports
/dev/cuau?.init
/dev/cuau?.lock corresponding callout initial-state and lock-state devices
SEE ALSO
puc(4), scc(4)
HISTORY
The uart device driver first appeared in FreeBSD 5.2.
AUTHORS
The uart device driver and this manual page were written by Marcel Moolenaar <marcel@xcllnt.net>.
Debian April 26, 2017 UART(4)