Provided by: freebsd-manpages_12.2-1_all 
NAME
sio — fast interrupt driven asynchronous serial communications interface
SYNOPSIS
For standard ISA ports:
device sio
In /boot/device.hints:
hint.sio.0.at="isa"
hint.sio.0.port="0x3f8"
hint.sio.0.flags="0x10"
hint.sio.0.irq="4"
hint.sio.1.at="isa"
hint.sio.1.port="0x2f8"
hint.sio.1.flags="0x0"
hint.sio.1.irq="3"
For AST compatible multiport cards with 4 ports:
options COM_MULTIPORT
device sio
In /boot/device.hints:
hint.sio.4.at="isa"
hint.sio.4.port="0x2a0"
hint.sio.4.flags="0x701"
hint.sio.5.at="isa"
hint.sio.5.port="0x2a8"
hint.sio.5.flags="0x701"
hint.sio.6.at="isa"
hint.sio.6.port="0x2b0"
hint.sio.6.flags="0x701"
hint.sio.7.at="isa"
hint.sio.7.port="0x2b8"
hint.sio.7.flags="0x701"
hint.sio.7.irq="12"
For Boca Board compatible multiport cards with 8 ports:
options COM_MULTIPORT
device sio
In /boot/device.hints:
hint.sio.4.at="isa"
hint.sio.4.port="0x100"
hint.sio.4.flags="0xb05"
...
hint.sio.11.at="isa"
hint.sio.11.port="0x138"
hint.sio.11.flags="0xb05"
hint.sio.11.irq="12"
For Netmos Nm9845 multiport cards with 6 ports:
options COM_MULTIPORT
device sio
In /boot/device.hints:
hint.sio.4.at="isa"
hint.sio.4.port="0xb000"
hint.sio.4.flags="0x901"
hint.sio.5.at="isa"
hint.sio.5.port="0xb400"
hint.sio.5.flags="0x901"
hint.sio.6.at="isa"
hint.sio.6.port="0xb800"
hint.sio.6.flags="0x901"
hint.sio.7.at="isa"
hint.sio.7.port="0xbc00"
hint.sio.7.flags="0x901"
hint.sio.8.at="isa"
hint.sio.8.port="0xc000"
hint.sio.8.flags="0x901"
hint.sio.9.at="isa"
hint.sio.9.port="0xac00"
hint.sio.9.flags="0x901"
hint.sio.9.irq="12"
For Hayes ESP cards:
options COM_ESP
device sio
...
For single port PCI and PCCARD cards:
device sio
No lines are required in /boot/device.hints for these cards.
For dual port PCI cards that share an interrupt:
device sio
options COM_MULTIPORT
In /boot/device.hints:
hint.sio.2.flags="0x201"
hint.sio.3.flags="0x201"
Meaning of flags:
0x00001 shared IRQs
0x00002 disable FIFO
0x00004 no AST/4 compatible IRQ control register
0x00008 recover sooner from lost output interrupts
0x00010 device is potential system console
0x00020 device is forced to become system console
0x00040 device is reserved for low-level IO (e.g. for remote kernel debugging)
0x00080 use this port for remote kernel debugging
0x0??00 minor number of master port
0x10000 PPS timestamping on CTS instead of DCD
0x20000 device is assumed to use a 16650A-type (extended FIFO) chip
DESCRIPTION
The sio driver provides support for NS8250-, NS16450-, NS16550 and NS16550A-based EIA RS-232C (CCITT
V.24) communications interfaces. The NS8250 and NS16450 have single character buffers, the NS16550A has
16 character FIFO input and output buffers.
Input and output for each line may set to one of following baud rates; 50, 75, 110, 134.5, 150, 300, 600,
1200, 1800, 2400, 4800, 9600, 19200, 28800, 38400, 57600, or 115200. Your hardware may limit your baud
rate choices.
The driver supports `multiport' cards. Multiport cards are those that have one or more groups of ports
that share an Interrupt Request (IRQ) line per group. Shared IRQs on different cards are not supported.
Frequently 4 ports share 1 IRQ; some 8 port cards have 2 groups of 4 ports, thus using 2 IRQs. Some
cards allow the first 2 serial ports to have separate IRQs per port (as per DOS PC standard).
Some cards have an IRQ control register for each group. Some cards require special initialization
related to such registers. Only AST/4 compatible IRQ control registers are supported. Some cards have
an IRQ status register for each group. The driver does not require or use such registers yet. To work,
the control and status registers for a group, if any, must be mapped to the scratch register (register 7)
of a port in the group. Such a port is called a master port.
The driver supports controller based PCI modems. The 3Com FaxModem PCI and the Advantec 56k Voice
Messaging PCI FaxModem are the only cards supported. WinModems, softmodems, hfc modems and any other
modems that are not controller based are not supported.
The flags keyword may be used on each device sio line in the kernel configuration file to disable the
FIFO on 16550A UARTs (see the synopsis). Disabling the FIFO should rarely be necessary.
The flags keyword must be used for all ports that are part of an IRQ sharing group. One bit specifies
IRQ sharing; another bit specifies whether the port does not require AST/4 compatible initialization.
The minor number of the device corresponding a master port for the group is encoded as a bitfield in the
high byte. The same master port must be specified for all ports in a group.
The irq specification must be given for master ports and for ports that are not part of an IRQ sharing
group, and not for other ports.
In the synopsis, flags 0x701 means that the 8th port (sio7) is the master port, and that the port is on a
multiport card with shared IRQs and an AST/4 compatible IRQ control register.
flags 0xb05 means that the 12th port (sio11) is the master port, and that the port is on a multiport card
with shared IRQs and no special IRQ control register.
Which port is the master port depends on the card type. Consult the hardware documentation of your card.
Since IRQ status registers are never used, and IRQ control registers are only used for AST/4 compatible
cards, and some cards map the control/status registers to all ports in a group, any port in a group will
sometimes do for the master port. Choose a port containing an IRQ status register for forwards
compatibility, and the highest possible port for consistency.
Serial ports controlled by the sio driver can be used for both `callin' and `callout'. For each port
there is a callin device and a callout device. The minor number of the callout device is 128 higher than
that of the corresponding callin port. The callin device is general purpose. Processes opening it
normally wait for carrier and for the callout device to become inactive. The callout device is used to
steal the port from processes waiting for carrier on the callin device. Processes opening it do not wait
for carrier and put any processes waiting for carrier on the callin device into a deeper sleep so that
they do not conflict with the callout session. The callout device is abused for handling programs that
are supposed to work on general ports and need to open the port without waiting but are too stupid to do
so.
The sio driver also supports an initial-state and a lock-state control device for each of the callin and
the callout "data" devices. The termios settings of a data device are copied from those of the
corresponding initial-state device on first opens and are not inherited from previous opens. Use stty(1)
in the normal way on the initial-state devices to program initial termios states suitable for your setup.
The lock termios state acts as flags to disable changing the termios state. E.g., to lock a flag
variable such as CRTSCTS, use stty crtscts on the lock-state device. Speeds and special characters may
be locked by setting the corresponding value in the lock-state device to any nonzero value. E.g., to
lock a speed to 115200, use “stty 115200” on the initial-state device and “stty 1” on the lock-state
device.
Correct programs talking to correctly wired external devices work with almost arbitrary initial states
and almost no locking, but other setups may benefit from changing some of the default initial state and
locking the state. In particular, the initial states for non (POSIX) standard flags should be set to
suit the devices attached and may need to be locked to prevent buggy programs from changing them. E.g.,
CRTSCTS should be locked on for devices that support RTS/CTS handshaking at all times and off for devices
that do not support it at all. CLOCAL should be locked on for devices that do not support carrier.
HUPCL may be locked off if you do not want to hang up for some reason. In general, very bad things
happen if something is locked to the wrong state, and things should not be locked for devices that
support more than one setting. The CLOCAL flag on callin ports should be locked off for logins to avoid
certain security holes, but this needs to be done by getty if the callin port is used for anything else.
FILES
/dev/ttyd? for callin ports
/dev/ttyd?.init
/dev/ttyd?.lock corresponding callin initial-state and lock-state devices
/dev/cuad? for callout ports
/dev/cuad?.init
/dev/cuad?.lock corresponding callout initial-state and lock-state devices
/etc/rc.d/serial examples of setting the initial-state and lock-state devices
The device numbers are made from the set [0-9a-v] so that more than 10 ports can be supported.
DIAGNOSTICS
sio%d: silo overflow. Problem in the interrupt handler.
sio%d: interrupt-level buffer overflow. Problem in the bottom half of the driver.
sio%d: tty-level buffer overflow. Problem in the application. Input has arrived faster than the given
module could process it and some has been lost.
SEE ALSO
stty(1), termios(4), tty(4), comcontrol(8)
HISTORY
The sio driver is derived from the HP9000/300 dca(4) driver and is currently under development.
BUGS
Data loss may occur at very high baud rates on slow systems, or with too many ports on any system, or on
heavily loaded systems when crtscts cannot be used. The use of NS16550A's reduces system load and helps
to avoid data loss.
Stay away from plain NS16550's. These are early implementations of the chip with non-functional FIFO
hardware.
The constants which define the locations of the various serial ports are holdovers from DOS. As shown,
hex addresses can be and for clarity probably should be used instead.
Note that on the AST/4 the card's dipswitches should not be set to use interrupt sharing. AST/4-like
interrupt sharing is only used when multiple AST/4 cards are installed in the same system. The sio
driver does not support more than 1 AST/4 on one IRQ.
The examples in the synopsis are too vendor-specific.
Debian August 30, 2006 SIO(4)