Provided by: freebsd-manpages_12.2-1_all 
NAME
wpi — Intel 3945ABG Wireless LAN IEEE 802.11 driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device wpi
device wpifw
device pci
device wlan
device wlan_amrr
device firmware
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_wpi_load="YES"
DESCRIPTION
The wpi driver provides support for the Intel 3945ABG Wireless network adapter. The driver supports
station, adhoc, adhoc-demo, hostap, and monitor mode operation. Only one virtual interface may be
configured at any time.
The wpi driver can be configured to use Wired Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA-PSK
and WPA2-PSK). WPA is the de facto encryption standard for wireless networks. It is strongly
recommended that WEP not be used as the sole mechanism to secure wireless communication, due to serious
weaknesses in it. The wpi driver offloads both encryption and decryption of data frames to the hardware
for the CCMP cipher.
This driver requires the firmware built with the wpifw 4 module to work.
The wpi driver can be configured at runtime with ifconfig(8).
FILES
/usr/share/doc/legal/intel_wpi.LICENSE wpi firmware license
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan0 create wlandev wpi0 inet 192.168.0.20 \
netmask 0xffffff00
Join a specific BSS network with network name “my_net”:
ifconfig wlan0 create wlandev wpi0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan0 create wlandev wpi0 ssid my_net \
wepmode on wepkey 0x1234567890 weptxkey 1 up
Create an IBSS network with 128-bit WEP encryption on the channel 4:
ifconfig wlan0 create wlandev wpi0 wlanmode adhoc ssid my_net \
wepmode on wepkey 0x01020304050607080910111213 weptxkey 1 \
channel 4
Join/create an 802.11b IBSS network with network name “my_net”:
ifconfig wlan0 create wlandev wpi0 wlanmode adhoc
ifconfig wlan0 inet 192.168.0.22 netmask 0xffffff00 ssid my_net \
mode 11b
Create an 802.11g host-based access point:
ifconfig wlan0 create wlandev wpi0 wlanmode hostap
ifconfig wlan0 inet 192.168.0.10 netmask 0xffffff00 ssid my_ap \
mode 11g
DIAGNOSTICS
wpi%d: could not load firmware image '%s' The driver failed to load the firmware image using the
firmware(9) subsystem. Verify the wpifw(4) firmware module is installed.
wpi%d: %s: timeout waiting for adapter to initialize, error %d The onboard microcontroller failed to
initialize in time. This should not happen.
wpi%d: %s: could not load boot firmware An attempt to upload the boot firmware image to the onboard
microcontroller failed. This should not happen.
wpi%d: device timeout A frame dispatched to the hardware for transmission did not complete in time. The
driver will reset the hardware and continue. This should not happen.
wpi%d: scan timeout Firmware scan command response was not received in time. The driver will reset the
hardware and continue. This should not happen.
wpi%d: fatal firmware error The onboard microcontroller crashed for some reason. The driver will reset
the hardware and continue. This should not happen.
wpi%d: RF switch: radio disabled The hardware switch controlling the radio is currently turned off.
Data transmission is not possible in this state.
wpi%d: can't map mem space The driver was unable to map the device registers into the host address
space. This should not happen.
wpi%d: can't map interrupt The driver was unable to allocate an IRQ for the device interrupt. This
should not happen.
wpi%d: can't establish interrupt, error %d The driver was unable to install the device interrupt
handler. This should not happen.
wpi%d: %s: bus_dmamap_load failed, error %d The driver was unable to map newly allocated mbuf to device
visible address space. Contents of currently received frame will be lost. This should not happen.
SEE ALSO
pci(4), wlan(4), wlan_amrr(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), wlan_xauth(4), wpifw(4),
hostapd(8), ifconfig(8), wpa_supplicant(8)
AUTHORS
The original wpi driver was written for OpenBSD by Damien Bergamini <damien.bergamini@free.fr>. Benjamin
Close <benjsc@FreeBSD.org> ported wpi to FreeBSD.
CAVEATS
Hostap mode is not directly supported by the device; it is implemented through IBSS mode (as a result,
DFS/passive channels are not available in this mode).
Powersave may be unstable on some networks (results in occasional 'wpi%d: device timeout' messages); you
can try to disable it to improve device stability.
Debian January 31, 2016 WPI(4)