Provided by: freebsd-manpages_12.2-1_all 
NAME
gpiobus — GPIO bus system
SYNOPSIS
To compile these devices into your kernel and use the device hints, place the following lines in your
kernel configuration file:
device gpio
device gpioc
device gpioiic
device gpioled
Additional device entries for the ARM architecture include:
device a10_gpio
device bcm_gpio
device imx51_gpio
device lpcgpio
device mv_gpio
device ti_gpio
device gpio_avila
device gpio_cambria
device zy7_gpio
device pxagpio
Additional device entries for the MIPS architecture include:
device ar71xxx_gpio
device octeon_gpio
device rt305_gpio
Additional device entries for the POWERPC architecture include:
device wiigpio
device macgpio
DESCRIPTION
The gpiobus system provides a simple interface to the GPIO pins that are usually available on embedded
architectures and can provide bit banging style devices to the system.
The acronym GPIO means “General-Purpose Input/Output.”
The BUS physically consists of multiple pins that can be configured for input/output, IRQ delivery,
SDA/SCL iicbus use, etc.
On some embedded architectures (like MIPS), discovery of the bus and configuration of the pins is done
via device.hints(5) in the platform's kernel config(5) file.
On some others (like ARM), where FDT(4) is used to describe the device tree, the bus discovery is done
via the DTS passed to the kernel, being either statically compiled in, or by a variety of ways where the
boot loader (or Open Firmware enabled system) passes the DTS blob to the kernel at boot.
On a device.hints(5) based system these hints can be used to configure drivers for devices attached to
gpiobus pins:
hint.driver.unit.at The gpiobus where the device is attached. For example, "gpiobus0". driver
and unit are the driver name and the unit number for the device driver.
hint.driver.unit.pins This is a bitmask of the pins on the gpiobus that are connected to the device.
The pins will be allocated to the specified driver instance. Only pins with
numbers from 0 to 31 can be specified using this hint.
hint.driver.unit.pin_list This is a list of pin numbers of pins on the gpiobus that are connected to the
device. The pins will be allocated to the specified driver instance. This is
a more user friendly alternative to the pins hint. Additionally, this hint
allows specifying pin numbers greater than 31. The numbers can be decimal or
hexadecimal with 0x prefix. Any non-digit character can be used as a
separator. For example, it can be a comma, a slash or a space. The separator
can be followed by any number of space characters.
The following device.hints(5) are only provided by the ar71xx_gpio driver:
hint.gpio.%d.pinmask This is a bitmask of pins on the GPIO board that we would like to expose for
use to the host operating system. To expose pin 0, 4 and 7, use the bitmask of
10010001 converted to the hexadecimal value 0x0091.
hint.gpio.%d.pinon This is a bitmask of pins on the GPIO board that will be set to ON at host
start. To set pin 2, 5 and 13 to be set ON at boot, use the bitmask of
10000000010010 converted to the hexadecimal value 0x2012.
hint.gpio.function_set
hint.gpio.function_clear These are bitmasks of pins that will remap a pin to handle a specific function
(USB, UART TX/RX, etc) in the Atheros function registers. This is mainly used
to set/clear functions that we need when they are set up or not set up by
uBoot.
Simply put, each pin of the GPIO interface is connected to an input/output of some device in a system.
SEE ALSO
gpioiic(4), gpioled(4), iicbus(4), device.hints(5), gpioctl(8)
HISTORY
The gpiobus manual page first appeared in FreeBSD 10.0.
AUTHORS
This manual page was written by Sean Bruno <sbruno@FreeBSD.org>.
Debian June 27, 2019 GPIO(4)