Ubuntu Manpage: em — Intel(R) PRO/1000 Gigabit Ethernet adapter driver

Provided by: freebsd-manpages_12.2-1_all

NAME

       em — Intel(R) PRO/1000 Gigabit Ethernet adapter driver

SYNOPSIS

       To compile this driver into the kernel, place the following lines in your kernel configuration file:

             device iflib
             device em

       Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

             if_em_load="YES"

DESCRIPTION

The em driver provides support for PCI Gigabit Ethernet adapters based on the Intel 82540, 82541ER,
82541PI, 82542, 82543, 82544, 82545, 82546, 82546EB, 82546GB, 82547, 82571, 81572, 82573, and 82574
Ethernet controller chips.

The em driver also provides support for PCI Express Gigabit Ethernet adapters based on the Intel 82575,
82576, 82580, i21x and i35x.

The driver supports Transmit/Receive checksum offload and Jumbo Frames on all but 82542-based adapters.

Furthermore it supports TCP segmentation offload (TSO) on all adapters but those based on the 82543,
82544 and 82547 controller chips. The identification LEDs of the adapters supported by the em driver can
be controlled via the led(4) API for localization purposes. For further hardware information, see the
README included with the driver.

For questions related to hardware requirements, refer to the documentation supplied with your Intel
PRO/1000 adapter. All hardware requirements listed apply to use with FreeBSD.

Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500
bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames. The
maximum MTU size for Jumbo Frames is 16114.

This driver supports hardware assisted VLANs. The em driver supports the following media types:

autoselect Enables auto-negotiation for speed and duplex.

10baseT/UTP Sets 10Mbps operation. Use the mediaopt option to select full-duplex mode.

100baseTX Sets 100Mbps operation. Use the mediaopt option to select full-duplex mode.

1000baseSX Sets 1000Mbps operation. Only full-duplex mode is supported at this speed.

1000baseTX Sets 1000Mbps operation. Only full-duplex mode is supported at this speed.

The em driver supports the following media options:

full-duplex Forces full-duplex operation

half-duplex Forces half-duplex operation.

Only use mediaopt to set the driver to full-duplex. If mediaopt is not specified, the driver defaults to
half-duplex.

For more information on configuring this device, see ifconfig(8).

HARDWARE

       The  em  driver  supports  Gigabit  Ethernet  adapters based on the Intel 82540, 82541ER, 82541PI, 82542,
       82543, 82544, 82545, 82546, 82546EB, 82546GB, 82547, 82571, 82572, 82573, 82574, 82575, 82576, and  82580
       controller chips:

       •   Intel Gigabit ET Dual Port Server Adapter (82576)
       •   Intel Gigabit VT Quad Port Server Adapter (82575)
       •   Intel Single, Dual and Quad Gigabit Ethernet Controller (82580)
       •   Intel i210 and i211 Gigabit Ethernet Controller
       •   Intel i350 and i354 Gigabit Ethernet Controller
       •   Intel PRO/1000 CT Network Connection (82547)
       •   Intel PRO/1000 F Server Adapter (82543)
       •   Intel PRO/1000 Gigabit Server Adapter (82542)
       •   Intel PRO/1000 GT Desktop Adapter (82541PI)
       •   Intel PRO/1000 MF Dual Port Server Adapter (82546)
       •   Intel PRO/1000 MF Server Adapter (82545)
       •   Intel PRO/1000 MF Server Adapter (LX) (82545)
       •   Intel PRO/1000 MT Desktop Adapter (82540)
       •   Intel PRO/1000 MT Desktop Adapter (82541)
       •   Intel PRO/1000 MT Dual Port Server Adapter (82546)
       •   Intel PRO/1000 MT Quad Port Server Adapter (82546EB)
       •   Intel PRO/1000 MT Server Adapter (82545)
       •   Intel PRO/1000 PF Dual Port Server Adapter (82571)
       •   Intel PRO/1000 PF Quad Port Server Adapter (82571)
       •   Intel PRO/1000 PF Server Adapter (82572)
       •   Intel PRO/1000 PT Desktop Adapter (82572)
       •   Intel PRO/1000 PT Dual Port Server Adapter (82571)
       •   Intel PRO/1000 PT Quad Port Server Adapter (82571)
       •   Intel PRO/1000 PT Server Adapter (82572)
       •   Intel PRO/1000 T Desktop Adapter (82544)
       •   Intel PRO/1000 T Server Adapter (82543)
       •   Intel PRO/1000 XF Server Adapter (82544)
       •   Intel PRO/1000 XT Server Adapter (82544)

LOADER TUNABLES

Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).

hw.em.disable_crc_stripping
Disable or enable hardware stripping of CRC field. This is mostly useful on BMC/IPMI shared
interfaces where stripping the CRC causes remote access over IPMI to fail. Default 0 (enabled).

hw.em.eee_setting
Disable or enable Energy Efficient Ethernet. Default 1 (disabled).

hw.em.msix
Enable or disable MSI-X style interrupts. Default 1 (enabled).

hw.em.smart_pwr_down
Enable or disable smart power down features on newer adapters. Default 0 (disabled).

hw.em.sbp
Show bad packets when in promiscuous mode. Default 0 (off).

hw.em.rxd
Number of receive descriptors allocated by the driver. The default value is 1024 for adapters
newer than 82547, and 256 for older ones. The 82542 and 82543-based adapters can handle up to
256 descriptors, while others can have up to 4096.

hw.em.txd
Number of transmit descriptors allocated by the driver. The default value is 1024 for adapters
newer than 82547, and 256 for older ones. The 82542 and 82543-based adapters can handle up to
256 descriptors, while others can have up to 4096.

hw.em.rx_int_delay
This value delays the generation of receive interrupts in units of 1.024 microseconds. The
default value is 0, since adapters may hang with this feature being enabled.

hw.em.rx_abs_int_delay
If hw.em.rx_int_delay is non-zero, this tunable limits the maximum delay in which a receive
interrupt is generated.

hw.em.tx_int_delay
This value delays the generation of transmit interrupts in units of 1.024 microseconds. The
default value is 64.

hw.em.tx_abs_int_delay
If hw.em.tx_int_delay is non-zero, this tunable limits the maximum delay in which a transmit
interrupt is generated.

FILES

       /dev/led/em*  identification LED device nodes

EXAMPLES

       Make the identification LED of em0 blink:

             echo f2 > /dev/led/em0

       Turn the identification LED of em0 off again:

             echo 0 > /dev/led/em0

DIAGNOSTICS

       em%d: Unable to allocate bus resource: memory  A fatal initialization error has occurred.

       em%d: Unable to allocate bus resource: interrupt  A fatal initialization error has occurred.

       em%d: watchdog timeout -- resetting  The device has stopped responding to the  network,  or  there  is  a
       problem with the network connection (cable).

SUPPORT

       For general information and support, go to the Intel support website at: http://support.intel.com.

       If an issue is identified with the released source code on the supported kernel with a supported adapter,
       email the specific information related to the issue to ⟨freebsd@intel.com⟩.

HISTORY

       The  em  device  driver  first  appeared  in  FreeBSD  4.4.  em was merged with the igb device driver and
       converted to the iflib framework in FreeBSD 12.0.

AUTHORS

       The em driver was originally written by Intel Corporation <freebsd@intel.com>.  It was  merged  with  igb
       driver  and  converted  to  the  iflib  framework  by  Matthew  Macy  <mmacy@mattmacy.io>  and Sean Bruno
       <sbruno@FreeBSD.org>.

Debian                                          January 30, 2019                                           EM(4)