NAME

       ganesha-cache-config - NFS Ganesha Cache Configuration File

SYNOPSIS

       /etc/ganesha/ganesha.conf

DESCRIPTION

       NFS-Ganesha reads the configuration data from: | /etc/ganesha/ganesha.conf

       This  file lists NFS-Ganesha Cache config options.  These options used to be configured in the CACHEINODE
       block.  They may still be used in that block, but it is deprecated and will go away.  The  MDCACHE  block
       takes precidence over the CACHEINODE block.

   MDCACHE {}
       NParts (uint32, range 1 to 32633, default 7)
              Partitions in the Cache_Inode tree.

       Cache_Size(uint32, range 1 to UINT32_MAX, default 32633)
              Per-partition hash table size.

       Use_Getattr_Directory_Invalidation(bool, default false)
              Use getattr for directory invalidation.

       Dir_Chunk(uint32, range 0 to UINT32_MAX, default 128)
              Size of per-directory dirent cache chunks, 0 means directory chunking is not enabled.

       Detached_Mult(uint32, range 1 to UINT32_MAX, default 1)
              Max number of detached directory entries expressed as a multiple of the chunk size.

       Entries_HWMark(uint32, range 1 to UINT32_MAX, default 100000)
              The point at which object cache entries will start being reused.

       Entries_Release_Size(uint32, range 0 to UINT32_MAX, default 100)
              The  number  of  entries  attempted  to  release  each time when the handle cache has exceeded the
              entries high water mark.

       Chunks_HWMark(uint32, range 1 to UINT32_MAX, default 100000)
              The point at which dirent cache chunks will start being reused.

       LRU_Run_Interval(uint32, range 1 to 24 * 3600, default 90)
              Base interval in seconds between runs of the LRU cleaner thread.

       FD_Limit_Percent(uint32, range 0 to 100, default 99)
              The percentage of the system-imposed maximum of  file  descriptors  at  which  Ganesha  will  deny
              requests.

       FD_HWMark_Percent(uint32, range 0 to 100, default 90)
              The  percentage  of  the  system-imposed maximum of file descriptors above which Ganesha will make
              greater efforts at reaping.

       FD_LWMark_Percent(uint32, range 0 to 100, default 50)
              The percentage of the system-imposed maximum of file descriptors below which Ganesha will not reap
              file descriptors.

       Reaper_Work(uint32, range 1 to 2000, default 0)
              Roughly, the amount of work to do on  each  pass  through  the  thread  under  normal  conditions.
              (Ideally,  a  multiple  of  the  number  of  lanes.)   This  setting  is  deprecated.   Please use
              Reaper_Work_Per_Lane

       Reaper_Work_Per_Lane(uint32, range 1 to UINT32_MAX, default 50)
              This is the numer of handles per lane to scan when  performing  LRU  maintenance.   This  task  is
              performed by the Reaper thread.

       Biggest_Window(uint32, range 1 to 100, default 40)
              The largest window (as a percentage of the system-imposed limit on FDs) of work that we will do in
              extremis.

       Required_Progress(uint32, range 1 to 50, default 5)
              Percentage of progress toward the high water mark required in in a pass through the thread when in
              extremis

       Futility_Count(uint32, range 1 to 50, default 8)
              Number of failures to approach the high watermark before we disable caching, when in extremis.

       Dirmap_HWMark(uint32, range 1 to UINT32_MAX, default 10000)
              The  point  at  which  dirmap  entries  are  reused.  This puts a practical limit on the number of
              simultaneous readdirs that may be in progress on an export for a  whence-is-name  FSAL  (currently
              only FSAL_RGW)

SEE ALSO

       ganesha-config(8)

                                                  Oct 26, 2022                           GANESHA-CACHE-CONFIG(8)